Hp Integrity Superdome 2 Server Uživatelský manuál

HP Integrity Superdome 2 OnboardAdministrator User GuideAbstractThis document contains specific information that is intended for users of this HP prod

IMPORTANT: You cannot update firmware through the HP Superdome 2 OnboardAdministrator GUI if you have complex firmware earlier than the Online Firmwar

DescriptionItemThe spare part number to use when ordering an additional or replacement OnboardAdministrator.Spare Part NumberThe unique serial number

TCP/IP Settings screenThis screen displays the current enclosure TCP/IP settings for the active Onboard Administrator.To change these settings, select

Certificate Administration screenInformation tabThis screen displays the detailed information of the SSL certificate now in use by the OnboardAdminist

DescriptionItemVersion number of current certificate.VersionA validation of authenticity embedded in the certificate.MD5 FingerprintA validation of au

Requied InformationDescriptionPossible valuesItemA valid country code that identifies the countrywhere the Onboard Administrator is located.Must be on

DescriptionPossible valuesItemcertificate. For example, if the web address inthe address box ishttps://oa-001635.xyz.com, then the valuemust be oa-001

When submitting the request to the certificate authority, be sure to:• Use the Onboard Administrator URL for the server.• Request the certificate be g

• Enclosure Event 0x07: Administrator Rights Changed• Enclosure Event 0x08: Enclosure Shutdown Pending• Enclosure Event 0x09: Enclosure Topology Chang

• Blade Event 0x110: Blade Device Information Changed• Blade Event 0x111: Blade Bay Management Processor Changed• Blade Event 0x112: ILO Ready• Blade

• Enclosure Event 0x1204: Flash Complete• Enclosure Event 0x1210: Non-iLo EBIPALog Options tabThis screen enables you to send system log messages to a

Outgoing portIncoming portProtocol17988Virtual media from PC to OA514Remote syslogLDAP and Remote syslog port number can be changed.If a protocol is d

and write them down. When looking at the enclosure from the rear, the bay on the left is bay 1,while the bay on the right is bay 2. When the Active On

Device baysDevice Bay Overview screenDevice Bay SummaryIn the Systems and Devices menu, the Device Bays category lists all blades in the enclosure. Se

DescriptionItemNOTE: Not applicable for HP Integrity Superdome 2 server blades or storage blades.Information on this page is current as of the last do

The enclosure media can be connected to multiple blades at the same time. Various USB key ISOfiles can be attached to various servers at the same time

Port Mapping InformationInformation regarding port mapping for all devices in the device bay is available by clicking thePort Mapping Information link

DescriptionItemThe server blade has been placed in the wrong slot in the enclosure according to thecurrent fan configuration. Possible values are OK o

DescriptionItemThe status of the FRU data for the DIMM. Possible values are Unknown, OK, Degradedor Failed.FRU Read StatusThe indictment status of the

Device InformationDescriptionRowServer bladeBlade TypeName of the company that manufactured the server bladeManufacturerCommon descriptive name for th

Table 9 CPU Information (continued)DescriptionItemFactory serial number of the processorSerial NumberManufacturing reference numberEngineering DateCod

select individual interconnects. After the appropriate interconnects are selected, the Virtual Poweror UID state drop-down can be selected to perform

keying errors. For interconnect modules, Onboard Administrator provides virtual power control,dedicated serial consoles, and management Ethernet conne

Interconnect Bay Status tabStatus informationDescriptionItemThe overall status of the interconnect device. Possible values are Unknown, OK, Degraded,a

Interconnect Bay Information tabHardware InformationDescriptionItemThe common descriptive name of the interconnect device.Product NameIP address of th

DescriptionItemIndicates whether or not the interconnect device has a temperature sensor.Temperature SensorThe firmware version of the interconnect mo

Graphical viewWhen you mouse over the port on the interconnect, the graphical view provides the same informationthat appears in the tabular view.Tabul

The check box in the first column on the top row toggles all check boxes on or off for all XFMs.This feature is useful if you want to toggle the UID s

XFM Bay Status tabStatus informationDescriptionRowThe overall status of the XFM. Possible values are Unknown,OK, Degraded, and Failed.StatusThe therma

DescriptionRowTemperature is above the danger threshold. Possible valuesare OK or Critical Temperature Threshold Reached.Overheat CheckThere is insuff

GPSM baysGPSM Bay Summary screenIn the Enclosure Information menu, the GPSM Bays category lists the Global Partition Servicesmodules within the select

GPSM Bay Information screenThe GPSM Bay Information screen displays information about the bays where GPSMs can beplaced.GPSM Status tabStatus informat

GPSM Bay Information tabDevice informationDescriptionItemThe common descriptive name of the GPSM.Product NameThe part number to be used when ordering

All Superdome 2 enclosures support two enclosure link connectors that provide privatecommunications among enclosures linked with CAT5 cable. In additi

For proper installation of the power supplies into a compute enclosure, see the HP IntegritySuperdome 2 Installation Guide.Power and Thermal screenDes

Power Management screenTo set the power management options in Onboard Administrator, go to the menu on the left andselect the enclosure to be managed,

DescriptionInsight DisplaynameModeto full performance. This mode is not supported for low voltage on theSuperdome 2 enclosure.An optional setting to l

DescriptionItemThe amount of power available for all devices in the enclosure measured in watts.Power AvailableThe amount of power available for measu

This screen provides status on the power subsystem and on each individual power supply.Power Subsystem informationDescriptionItemThe status of the pow

DescriptionItemThis value is a measure of the present output of the power supply in watts.Present Output (Watts)The amount of power provided by the po

DescriptionItemThe part number to be used when ordering an additional or replacement power supply ofthis type.Part NumberThe spare part number to be u

Fan subsystem statusDescriptionRowIndicates the overall status of the fan subsystem. Possible values are Unknown, OK,Degraded, or Critical Error.Therm

138 Configuring HP Integrity Superdome 2 compute enclosures and enclosure devices

Fan speeds appear in percentage of total capacity, and fans operating in a zone without anyblades run at a minimum RPM of 30% to maintain proper cooli

Onboard Administrator requires the user to log in to the web GUI or CLI with an account andpassword. The account can be a local account where the pass

Selecting a specific power supply opens the Power Supply Information, Bay x page, where x isthe bay of the selected power supply. This screen provides

User roles and privilege levelsWithin the Users/Authentication category of HP Superdome 2 Onboard Administrator, you canaccess the Local Users subcate

Permissions for interconnect modules are slightly different. Autologin is not supported for interconnectmodules, and all user levels have access to th

Click the Add User button to save settings. The Edit Local User screen appears.Edit Local UserUser informationDescriptionPossible valueItemA maximum o

DescriptionPossible valueItemAdministratorPrivilege Level• Only the Administrator, with OnboardAdministrator Bays permission, can set theuser privileg

Check boxesSelecting the device base bay check box does not give the user permission to a double-denseserver without also selecting A and B for that b

Directory Settings screenLDAP is a protocol for accessing information directories. While LDAP is based on the X.500standard, it is significantly simpl

…output truncated…-----END CERTIFICATE-----8. Return to the Onboard Administrator, paste the certificate contents into the window, and clickthe Upload

A successful test reports that Onboard Administrator is able to resolve the Directory Server hostname using domain name.A failed test reports that Onb

A failed test reports that the authenticated user does not have any authorization on OnboardAdministrator because the user does not belong to any of t

Logging on to the Onboard Administrator GUIEnter the user name and initial administration password for your HP Superdome 2 OnboardAdministrator accoun

• New: Click the New buttonto add a new Directory Group to the selected enclosure. You canadd a maximum of 30 Directory Groups. The Add LDAP Group scr

Group PermissionsDescriptionCheck boxGives the user permissions for the Onboard Administratorbays and enables the user to see the fans and powerOnboar

DescriptionItem• Cannot change any configuration settings.• Without Onboard Administrator Bays permission, can manage only devices and interconnectsto

This page lists the owner of each authorized Secure Shell key and enables adding new keys.• SSH Fingerprint: Lists the public key portion of a public/

Edit Local User Certificate Information tabWhen Two-Factor Authentication is enabled, a user must have a user certificate to log on to theOnboard Admi

DescriptionRowSubject nameSubject OrganizationOrganization to whom the certificate was issuedIssued ToThe date from which the certificate is validVali

• Delete Users: Select a user or users to be deleted by selecting the check box next to the nameof the user, and click the Delete Users button. You ca

8 HP Integrity Superdome 2 IOX EnclosuresEach IOX enclosure in the complex can be selected from the left navigation tree. Clicking the IOXname opens t

DescriptionItemTemperature is above the warning threshold. Possible values are OK or TemperatureWarning.TemperatureTemperature is above the danger thr

DescriptionItemThe part number to be used when ordering an additional IOX enclosure of this type.Part NumberThe part number to be used when ordering a

For more information, see “First Time Setup Wizard” (page 41).Using online helpTo access online help, click the blue box with the white question mark

IOX Power Subsystem screenThe Power Subsystem screen shows the overall status of the IOX enclosure power subsystem andinformation about each power sup

DescriptionItemThis value is a measure of the present output of the power supply in watts.Present Output (Watts)The amount of power provided by the po

Thermal Subsystem informationDescriptionItemIndicates the overall status of the fan subsystem. Possible values are Unknown, OK,Degraded, or Critical E

9 Port mappingDevice bay port mapping for Superdome 2 Compute EnclosuresSuperdome 2 Server BladeIn this diagram, N equals the number of the blade in t

10 Using the CLICommand line overviewThe Onboard Administrator CLI is available from the Onboard Administrator serial port, managementport, or service

11 Using the serial connectionSetting up Onboard Administrator using the CLI1. Connect to the Onboard Administrator CLI using the serial port, managem

DescriptionDirectionNamePinTransmit dataOutTXD3Data terminal readyOutDTR4System groundGND5Data set readyInDSR6Request to sendOutRTS7Clear to sendInCTS

12 Using configuration scriptsConfiguration scriptsConfiguration scripts are useful for preserving settings and configuration information, particularl

Current enclosure inventoryTo download a script of the current enclosure inventory, click the Click here link, and then thecurrent enclosure inventory

13 TroubleshootingOnboard Administrator error messagesThe error message types are:• Soap Response Errors: These are the general errors reported by the

Recovering the administrator passwordIf the administrator password has been lost, you can reset the administrator password to the factorydefault that

26 The submitted value is too long.27 The submitted trap receiver already exists.28 The maximum number of trap receivers already exists.29 The maximum

68 Getting interconnect information for the submitted interconnect failed.69 Getting interconnect status for the submitted interconnect failed.70 An e

110 Setting power information failed.111 Getting User Note text failed.112 Setting User Note text failed.113 Getting the User Note bitmap failed.114 S

153 A blade boot device can only be listed once.154 NTP Poll time must be between 60 and 9999 seconds.155 Could not create new file.156 Could not writ

214 The certificate exceeds maximum size accepted.215 Could not reset the blade's efuse.216 Firmware Update in progress. Sign In disabled.217 An

265 Certificate has not been mapped to this user account.266 Two-Factor Authentication is in Effect. Please close the browser and try to login.267 Two

612 This operation cannot be performed unless the partition is running.613 This partition operation is not supported.614 Partition is busy at this tim

813 Specified blade or IO Bay is not a member of this partition.814 Specified resource is current deconfigured.815 Invalid resource type specification

1006 Invalid indictment status.1007 The number is not a valid CPU number.1008 Invalid complex type.1009 Getting blade firmware Information failed.1010

Resetting the Onboard Administrator to factory defaults also resets any certificates on the OnboardAdministrator.Onboard Administrator SNMP trapsThe H

2 HP Integrity Superdome 2 Insight DisplayHP Integrity Superdome 2 Insight Display componentsFunctionDescriptionItemDisplays Main Menu error messagesa

DescriptionTrap nameTrap IDBlade requested too low powercpqRackServerBladeToLowPower22049Blade removedcpqRackServerBladeRemoved222050Blade insertedcpq

14 Enabling LDAP Directory Services Authentication toMicrosoft Active DirectoryCertificate ServicesThe Microsoft implementation of LDAP over SSL requi

1. Navigate to the Directory Settings screen for the enclosure located under Users/Authentications.2. Click Enable LDAP and then enter the IP address

4. Click the Details tab, and then click theCopy to File... button.5. IMPORTANT: Select Base-64 encoded x.509 (.CER) from the list of export options.

qTvgisrZeHtvmrmecvSxZm27b4Bj5XYN0VYcrwqKnH7X/tVhmwqGls7/YZyahNU1lGB2OjoCq5eJxX+Ybx0CAwEAAaOCA00wggNJMAsGA1UdDwQEAwIFoDBEBgkqhkiG9w0BCQ8ENzA1MA4GCCqGSI

Testing the directory login solution1. Log out of the current Onboard Administrator session, and then close all browser windows.2. Browse to the Onboa

is operating properly on a Domain Controller (for example, a Certificate has been issued to it),you are prompted by the Security dialog whether you wa

15 Support and other resourcesBefore you contact HPBe sure to have the following information available before you call HP:• Technical support registra

diagnosis, and automatic, secure submission of hardware event notifications to HP, which willinitiate a fast and accurate resolution, based on your pr

Variable The name of a placeholder in a command, function, or other syntax displaythat you replace with an actual value.WARNING! A warning calls atten

When the enclosure UID is on, the Insight Display flashes after two minutes of inactivity.Pressing any button on the Insight Display stops the blinkin

A Time zone settingsAfrica time zone settingsNOTE: Time zones must be entered exactly as they appear.The following table provides the African time zon

America/Thunder_BayAmerica/La_PazAmerica/BogotaAmerica/TijuanaAmerica/LimaAmerica/BoiseAmerica/TortolaAmerica/Los_AngelesAmerica/Buenos_AiresAmerica/V

US/MountainAmerica/RosarioAmerica/HermosilloUS/PacificAmerica/SantiagoAmerica/Indiana/IndianapolisAsia time zone settingsNOTE: Time zones must be ente

UTCEtc/ZuluEtc/GMT+10Etc/GMT-5Etc/GMT0WETGMTEtc/GMT-11Etc/GMT+5Etc/GMT-0W-SUGreenwichEtc/GMT+11Etc/GMT-6Etc/GMT+0ZuluHSTEtc/GMT-12Etc/GMT+6Etc/GMT-1-M

The following table provides the European time zone settings that are supported by the OnboardAdministrator.Europe/VaduzEurope/ParisEurope/HelsinkiEir

Standard terms, abbreviations, and acronymsBIOS Basic Input/Output System.Btu British thermal unit.CA Certificate authority.CRL Certificate revocation

IndexAActive Onboard Administrator certificate upload tab, 106active onboard administrator screen, 98active to standby, 98AlertMail screen, 83alertsCo

IOX information, 158IOX power and thermal, 159IOX power subsystem, 160IOX status, 157IOX thermal subsystem, 161LLDAP group testing, 147link loss failo

© Copyright 2010 – 2013 Hewlett-Packard Development Company, L.P.NoticesThe information contained herein is subject to change without notice. The only

TIP: Select the ? icon to access detailed help information about each setting or topic.TIP: Within any menu option, navigate the cursor to What is Thi

• Enclosure Name— The default setting is a unique factory-assigned name. The acceptedcharacter values are 0-9, A-Z ,a-z, -, _, and the box character.

6. Be sure that all components are installed and cabled before continuing. Select Continue, andpress the OK button to begin verifying for configuratio

10. Navigate to Help, and then press OK to view the Help: DVD Connection screen.• An exclamation icon indicates no DVD drive and disk is detected or f

• View User Note• Chat ModeIf the active Onboard Administrator detects a USB key drive with any *.ROM , *.CFG or *.ISOfiles, then a USB menu item appe

Select Next Alert from the navigation bar, and press the OK button to view each individual errorcondition. The Insight Display displays each error con

• Enclosure Name• Rack Name• DVD Drive• Insight Display PIN#NOTE: The DVD Drive setting can attach or detach a CD or DVD loaded in the DVD driveto any

Blade and Port Info screenThe Blade and Port Info screen displays information about a specific server blade. On the firstscreen, select the server bla

To view the ports used by a specific server blade, select Port Info, and then press the OK button.The following screen shows a server blade with four

Selecting Turn Enclosure UID Off from the main menu turns off the rear enclosure UID LED andchanges the color of the Insight Display screen to the cur

Contents1 Introduction...8Overview...

Insight Display errorsThe enclosure installation is successful when all errors are corrected. The errors in the followingsections are specific to inst

1. Use the arrow buttons to navigate to Fix This, and press OK.2. Review and complete the corrective action suggested by the Insight Display. In most

3 HP Superdome 2 Door Status DisplayHP Superdome 2 SD2-16s and SD2-32s complexes that are factory integrated ship with the HPSuperdome 2 Door Status D

The startup menu has the following options:• Disable Display—A screen saver immediately appears for one hour, and then the Door Displayshuts off.• Set

IMPORTANT: This menu selection does not set the complex configuration on the OnboardAdministrator. To correctly set up the Door display, you must sele

If you selected Two 16s as the complex configuration, then you are prompted to which complexdisplays status information on the Door Display screen.• L

Complex loginYou must enter an OA account user name and password to enable the Door Display to log in tothe complex and display complex status informa

The Door Display status menu displays the following information:• Complex name—The user-specified name of the complex.• Complex health—The current hea

Display Settings menuIMPORTANT: Accessing the Display Settings screen requires a valid door display login even ifno settings are changed. If you cance

◦ Update Available— A newer firmware revision is available for the Door Display.◦ No Update Available— The OA does not have firmware available for the

Directory Groups screen...48Directory Settings

When the firmware update is complete, you are prompted to reboot the Door Display to completethe firmware update. To reboot the Door Display only, pre

4 First Time Setup WizardNOTE: The First Time Setup Wizard is used only to configure compute enclosures and OnboardAdministrator network settings. The

If more than one enclosure is listed on the Enclosure Selection screen, select the enclosure you wantto set up, and then click the Next button.For pos

On the Configuration Management screen, select one of the following options:• Local file: Browse for the configuration file, or enter the path of the

DescriptionPossible valueBoxIP address of primary NTP server thatprovides date and time information###.###.###.### where ### ranges from 0 to 255Prima

DescriptionPossible valueBoxThe password for the Administratoraccount3 to 8 characters including allprintable charactersPasswordMust match the Passwor

• New: Click the New button to add a new user to the selected enclosure. A maximum of 30user accounts can be added including the reserved accounts. Th

Enclosure Bay IP Addressing screenThe Onboard Administrator EBIPA feature is intended to help you provision a fixed IP address toa particular bay in a

EBIPA Settings screenFor information on how to set up EBIPA, see (page 91).Directory Groups screenLDAP is an open protocol for accessing information d

On this screen, you can configure directory groups.For possible values and descriptions of each box, see “Directory Groups” (page 149).Directory Setti

AlertMail screen...83Device Power Sequenc

Onboard Administrator Network Settings screenUse the Onboard Administrator Network Settings screen to modify network settings for all theOnboard Admin

For possible values and descriptions of each box, see “SNMP Settings screen” (page 94).Power Management screenIMPORTANT: In a complex with one or more

The Superdome 2 enclosure power management system enables you to customize the configurationof the enclosure. You can select from the various modes on

DescriptionInsight Display nameModethat an ac line feed failure does not cause the enclosure to poweroff.Up to six upper and six lower power supplies

Click the Finish button to save and exit the First Time Setup Wizard. The First Time Setup Wizardscreen closes and you are returned to the default mai

5 Navigating Onboard AdministratorNavigation overviewThe main HP Superdome 2 Onboard Administrator navigation system consists two views:• Tree view: L

One of the main purposes of the tree view is to enable navigation using categories based on themajor systems within the complex. When a category is ex

Category summary pagesCategory summary pages contain summary information for each of the devices in that category.For example, clicking the Device Bay

Selecting a deviceTo select a device, click the graphical representation of the device in the front or rear graphicalview. When you select a device, i

and a padlock icon appears in the bay table cell, indicating that the bay is locked to the currentuser.The user cannot select a locked bay. When the u

Power Management screen...131Enclosure Power Allocation screen

6 Complex OverviewComplex Overview screenThe Complex Overview screen displays a graphical representation of each compute enclosure inthe complex, call

Compute Enclosures tabDescriptionItemThe DNS name of the enclosure and the name of the enclosure in the rack.Enclosure NameThe ID for the Enclosure in

Table 2 Compute enclosure cooling requirementsDescriptionItemThe sum of the amount of heat being generated by the complex enclosures measured inBtu pe

Table 3 Compute enclosure thermal and power status (continued)DescriptionItemThe amount of watts being consumed by all devices in the enclosure.Presen

DescriptionItemThe overall health of the complex. Possible values are Unknown, OK, Degraded, and Failed.Complex StatusThe overall health of the CAMNET

Enclosure Status OverviewDescriptionColumnThe number of the compute enclosure in the complex.Enclosure NumberThe assigned name of the compute enclosur

DescriptionItemCommon descriptive name of the Superdome 2 complexProduct NameName of the company that manufactured the complexManufacturerThe original

Complex Logs tabThe Complex Logs tab displays links to launch log viewers in new windows. The available logviewers are the System Event Log, Forward P

Table 4 Complex Firmware information (continued)DescriptionItemThe model number of the deviceModelThe currently installed version of the firmware on t

new partition firmware packages (system firmware) will require a partition reboot to activate, butthe timing of such an operation can be done on an in

12 Using configuration scripts...167Configuration scripts...

packages in the bundle which must be updated, but is not expected to exceed 150 minutes underany conditions. Typical firmware updates will take less t

ConsoleWhen the firmware update is in progress, the OS console cannot be serviced on the servermanagement side. Since all active sessions to the OA CL

Affected OS CommandsThe machinfo command can print the firmware versions. This command may malfunction duringan active online complex firmware update

1. Can Oracle use IPMI to reset a partition?• Answer: Not during the online complex firmware update process.2. Do virtual partition reboots proceed du

NOTE: This issue only pertains to newly created guests that have never been started. Guests thathave been started at least once prior to the Online Fi

To update complex firmware if you have complex firmware earlier than the Online FirmwareUpdate firmware release, see the UPDATE FIRMWARE section in th

If the analysis fails, you will not be supplied with further options.If the Analysis Only option was not selected, then the firmware update will autom

The following information will be displayed:• The status of each component being updated.• The total number of components that will be updated.• The n

the Onboard Administrator CLI or by navigating to the Complex nPartitions menu and selectingthe Virtual Devices tab.For more information, see the HP I

7 Configuring HP Integrity Superdome 2 compute enclosuresand enclosure devicesViewing the status screensEach compute enclosure in the complex can be s

1 IntroductionOverviewHP Superdome 2 Onboard Administrator is the complex management processor, subsystem, andfirmware base used to support HP Integri

• Unknown• InformationalEnclosure settingsEnclosure Settings screenThis section provides detailed procedures to configure the management functionality

Diagnostic informationDiagnostic information is gathered by polling a device microcontroller (resulting in a degradedstatus if a failure has occurred)

Enclosure Information tabDescriptionItemThe general description of the enclosure componentPartThe model name of the enclosure componentModelThe name o

Changing settingsYou can change enclosure settings from this screen. To save the settings after making the changes,click the Apply button.DescriptionP

NOTE: The Alert Sender Domain might not be required. The information in this box depends onthe mail server setup.DescriptionPossible valueBoxThis box

Where <SEVERITY> is one of the following (from highest to lowest):• # FATAL• # CRITICAL• # WARNING MAJOR• # WARNING MINOR• # WARNING• # NORMALEa

Typical use cases involving bay to bay dependencies that can be resolved by enabling the enclosurepower delay feature include:• Boot from network— Net

DescriptionColumnEnables power sequencing, disables power sequencing,or does not allow powering on of the device if No Poweronis selected.EnabledThe a

NTP settingsTo enable this feature, select Set time using an NTP server.DescriptionPossible valueBoxIP address of primary NTP server thatprovides date

• Enable Dynamic DNS— Enables you to use a DNS server to translate host names into IPaddresses• Static IP Settings— Enables you to manually set up sta

Table 1 Benefits of using a redundant Onboard Administrator versus a single Onboard Administrator(continued)Redundant OnboardAdministrator in enclosur

The Protocol Restrictions subcategory is used to restrict access to the Onboard Administrator. Upto four protocol settings can be selected to allow or

Anonymous Data tabEnable Extended Data on GUI Login Page— This check box is selected by default. Clearing thischeck box disables the "+" fun

The administrator sets an independent range for server blade bays and interconnect module baysusing the Onboard Administrator EBIPA setup wizard. The

Knowing your network configuration before setting up EBIPA ensures an easy setup and enablesyou to install your HP Superdome 2 Onboard Administrator o

Device listDescriptionColumnThe bay in the enclosure of the device.BayEnables EBIPA settings for the device bay. EBIPA settings for all device bays ca

The Enable SNMP check box is not selected by default. When enabled, the Onboard Administratorcan be polled for status and basic information. The SNMP

Edit any of the fields in this subcategory, and to save the changes, click the Apply button.SNMP Alert Destinations settingsIn the SNMP Alert Destinat

Current enclosure inventoryTo download a script of the current enclosure inventory, click the Click here link; the current enclosureinventory opens in

• Power supply• Insight DisplayActive to Standby screenWhen a second HP Superdome 2 Onboard Administrator is installed, the menu item Active toStandby

Diagnostic information is gathered by polling a device microcontroller (resulting in a degradedstatus if a failure has occurred) or is sent by the dev