Hp ProLiant BL465c Gen8 Server Blade Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Počítačový hardware Hp ProLiant BL465c Gen8 Server Blade. HP ProLiant BL465c Gen8 Server Blade User Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 89
  • Tabulka s obsahem
  • ŘEŠENÍ PROBLÉMŮ
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
HP ProLiant BL465c Gen8 Server Blade
User Guide
Abstract
This document is for the person who installs, administers, and troubleshoots servers and storage systems. HP assumes you are qualified in the
servicing of computer equipment and trained in recognizing hazards in products with hazardous energy levels.
Part Number: 661814-002
August 2012
Edition: 2
Zobrazit stránku 0
1 2 3 4 5 6 ... 88 89

Shrnutí obsahu

Strany 1 - User Guide

HP ProLiant BL465c Gen8 Server Blade User Guide Abstract This document is for the person who installs, administers, and troubleshoots servers and st

Strany 2

Component identification 10 CAUTION: Clearing CMOS and/or NVRAM deletes configuration information. Be sure to properly configure the server or dat

Strany 3 - Contents

Component identification 11 Tool location A Torx T-15 screwdriver is located on the DIMM baffle. HP c-Class Blade SUV Cable Item Connector D

Strany 4 - Contents 4

Operations 12 Operations Power up the server blade The Onboard Administrator initiates an automatic power-up sequence when the server blade is insta

Strany 5 - Contents 5

Operations 13 o poweroff server [bay number] force This form of the command forces the server blade to enter standby mode without properly exiting a

Strany 6 - Component identification

Operations 14 Remove the access panel To remove the component: 1. Power down the server blade (on page 12). 2. Remove the server blade (on page 13

Strany 7 - Front panel LEDs and buttons

Operations 15 5. Remove the DIMM baffle. Install the DIMM baffle 1. Install the DIMM baffle.

Strany 8 - System board components

Operations 16 2. Connect the drive cable connectors to the SAS controller. 3. Install the access panel (on page 14). 4. Install the server blade

Strany 9 - System maintenance switch

Operations 17 6. Extend the serial label pull tab from the front of the server blade. CAUTION: Always disconnect the drive cable before removin

Strany 10 - DIMM slot locations

Operations 18 2. Install the front panel/drive cage assembly and reconnect the drive cables. 3. Close the serial label pull tab. 4. Install the

Strany 11 - HP c-Class Blade SUV Cable

Operations 19 CAUTION: Always disconnect the drive cables from the SAS controller before removing the DIMM baffle. Failure to do so may result in

Strany 12 - Operations

© Copyright 2012 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties

Strany 13 - Remove the server blade

Operations 20 4. Connect the drive cables and the capacitor pack cables to the SAS controller. For more information, see "Cabling (on page 48).

Strany 14 - Remove the DIMM baffle

Operations 21 3. Remove drive 2. 4. Lift drive carrier 1 into position in the drive tray. 5. Slide the drive tray into the server blade. Close th

Strany 15 - Install the DIMM baffle

Setup 22 Setup Overview Installation of a server blade requires the following steps: 1. Install and configure an HP BladeSystem c-Class enclosure.

Strany 16

Setup 23 Interconnect bay numbering and device mapping • HP BladeSystem c7000 Enclosure To support network connections for specific signals, insta

Strany 17 - Operations 17

Setup 24 • HP BladeSystem c3000 Enclosure and Tower Enclosure Server blade signal Interconnect bay number Interconnect bay label Notes Flex

Strany 18 - Remove the SAS controller

Setup 25 Two types of interconnect modules are available for HP BladeSystem c-Class enclosures: Pass-Thru modules and switch modules. For more infor

Strany 19 - Install the SAS controller

Setup 26 2. Remove the enclosure connector cover. 3. Install the server blade. Completing the configuration To complete the server blade and HP

Strany 20 - Remove all drives

Hardware options installation 27 Hardware options installation Introduction If more than one option is being installed, read the installation instru

Strany 21 - Remove drive 2

Hardware options installation 28 2. Release the drive tray, slide it forward until it locks, and then press drive carrier 1 down to access drive bay

Strany 22 - Overview

Hardware options installation 29 4. Install the drive in drive bay 2. 5. Slide the drive tray into the server blade. Close the drive tray lever un

Strany 23

Contents 3 Contents Component identification ...

Strany 24 - Connecting to the network

Hardware options installation 30 Processor option WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the int

Strany 25 - Installing a server blade

Hardware options installation 31 8. Remove the heatsink blank. Retain the heatsink blank for future use. 9. Open the processor socket locking leve

Strany 26 - Completing the configuration

Hardware options installation 32 10. If the processor has separated from the installation tool, carefully re-insert the processor in the tool. Handl

Strany 27 - Drive option

Hardware options installation 33 12. Press the tabs on the processor tool to release the processor, and then remove the processor tool. 13. Close

Strany 28 - Prepare the drive

Hardware options installation 34 14. Remove the thermal interface protective cover from the heatsink. CAUTION: To avoid damage to the system bo

Strany 29 - 6. Install the drive

Hardware options installation 35 IMPORTANT: This server blade does not support mixing LRDIMMs or RDIMMs. Attempting to mix any combination of thes

Strany 30 - Processor option

Hardware options installation 36 Qualified memory is performance-tuned for HP ProLiant and BladeSystem servers and provides future enhanced support

Strany 31

Hardware options installation 37 DIMM identification To determine DIMM characteristics, use the label attached to the DIMM and the following illustr

Strany 32

Hardware options installation 38 is degrading. This allows DIMMs that have a higher probability of receiving an uncorrectable memory error (which wo

Strany 33

Hardware options installation 39 • When one processor is installed, install DIMMs in sequential alphabetic order: A, B, C, D, E, F, and so forth. •

Strany 34 - Memory options

Contents 4 Mezzanine card option ...

Strany 35 - HP SmartMemory

Hardware options installation 40 3. Remove the access panel (on page 14). 4. Remove the DIMM baffle (on page 14). 5. Open the DIMM slot latches. 6

Strany 36

Hardware options installation 41 4. Remove the mezzanine assembly from the server blade. 5. Align the mezzanine card with the guide pins on the me

Strany 37 - Memory configurations

Hardware options installation 42 6. Install the mezzanine card in the mezzanine assembly, and then tighten the mezzanine card screws to secure the c

Strany 38

Hardware options installation 43 3. Remove the access panel (on page 14). 4. Remove the DIMM baffle (on page 14). 5. Install the FBWC capacitor pa

Strany 39 - Installing DIMMs

Hardware options installation 44 o Route the cable between the DIMMs and the heatsinks or heatsink blank. Connect the cable to the mezzanine option.

Strany 40 - Mezzanine card option

Hardware options installation 45 CAUTION: Always observe the guidelines in this document. Failure to follow these guidelines can cause hardware da

Strany 41

Hardware options installation 46 7. Install the TPM board. Press down on the connector to seat the board ("System board components" on pag

Strany 42 - Capacitor pack option

Hardware options installation 47 • Always store copies of the recovery key/password away from the server blade. • Do not save the recovery key/pas

Strany 43

Cabling 48 Cabling Cabling resources Cabling configurations and requirements vary depending on the product and installed options. For more informati

Strany 44

Cabling 49 Drive cabling Using the HP c-Class Blade SUV Cable The HP c-Class Blade SUV Cable enables the user to perform server blade administrati

Strany 45

Contents 5 FCC rating label ...

Strany 46

Cabling 50 3. Connect a USB mouse to one USB connector. 4. Connect a USB keyboard to the second USB connector. Item Description 1 Monitor 2 U

Strany 47

Cabling 51 o USB mouse Item Description 1 Monitor 2 USB CD/DVD-ROM drive 3 USB keyboard 4 USB hub 5 USB mouse 6 HP c-Class Blade SUV Cable

Strany 48 - Cabling

Software and configuration utilities 52 Software and configuration utilities Server mode The software and configuration utilities presented in this

Strany 49 - USB devices

Software and configuration utilities 53 iLO enables and manages the Active Health System (on page 53) and also features Agentless Management. All ke

Strany 50

Software and configuration utilities 54 The data that is collected is managed according to the HP Data Privacy policy. For more information see the

Strany 51 - Item Description

Software and configuration utilities 55 HP Insight Diagnostics HP Insight Diagnostics is a proactive server blade management tool, available in both

Strany 52 - HP iLO Management Engine

Software and configuration utilities 56 HP Insight Remote Support software HP strongly recommends that you install HP Insight Remote Support softwar

Strany 53 - Active Health System

Software and configuration utilities 57 HP Service Pack for ProLiant SPP is a release set that contains a comprehensive collection of firmware and s

Strany 54 - Intelligent Provisioning

Software and configuration utilities 58 • Configuring memory options • Language selection For more information on RBSU, see the HP ROM-Based Setup

Strany 55 - Erase Utility

Software and configuration utilities 59 Boot options Near the end of the boot process, the boot options screen is displayed. This screen is visible

Strany 56 - Scripting Toolkit

Component identification 6 Component identification Front panel components Item Description 1 Serial label pull tab 2 HP c-Class Blade SUV con

Strany 57 - HP ROM-Based Setup Utility

Software and configuration utilities 60 Utilities and features Array Configuration Utility ACU is a utility with the following features: • Runs as

Strany 58 - Auto-configuration process

Software and configuration utilities 61 Option ROM Configuration for Arrays Before installing an operating system, you can use the ORCA utility to c

Strany 59 - Configuring AMP modes

Software and configuration utilities 62 Legacy USB support provides USB functionality in environments where USB support is not available normally. S

Strany 60 - Utilities and features

Software and configuration utilities 63 Software and firmware Software and firmware should be updated before using the server for the first time, un

Strany 61 - USB support

Troubleshooting 64 Troubleshooting Troubleshooting resources The HP ProLiant Gen8 Troubleshooting Guide, Volume I: Troubleshooting provides procedur

Strany 62 - Keeping the system current

Battery replacement 65 Battery replacement If the server blade no longer automatically displays the correct date and time, you might have to replace

Strany 63 - ProLiant Servers

Regulatory compliance notices 66 Regulatory compliance notices Regulatory compliance identification numbers For the purpose of regulatory compliance

Strany 64 - Troubleshooting

Regulatory compliance notices 67 radio communications. However, there is no guarantee that interference will not occur in a particular installation.

Strany 65 - Battery replacement

Regulatory compliance notices 68 This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. C

Strany 66 - FCC rating label

Regulatory compliance notices 69 This symbol on the product or on its packaging indicates that this product must not be disposed of with your other

Strany 67 - Modifications

Component identification 7 Front panel LEDs and buttons Item Description Status 1 Health status LED bar Solid Green = Normal (System is powere

Strany 68 - • EMC Directive 2004/108/EC

Regulatory compliance notices 70 Class B equipment Chinese notice Class A equipment Vietnam compliance marking notice This marking is for applic

Strany 69 - Korean notice

Regulatory compliance notices 71 WARNING: Use of controls or adjustments or performance of procedures other than those specified herein or in the

Strany 70 - Laser compliance

Regulatory compliance notices 72 Nach ISO 7779:1999 (Typprüfung)

Strany 71 - Battery replacement notice

Electrostatic discharge 73 Electrostatic discharge Preventing electrostatic discharge To prevent damaging the system, be aware of the precautions yo

Strany 72

Specifications 74 Specifications Environmental specifications Specification Value Temperature range* — Operating 10°C to 35°C (50°F to 95°F) Non-

Strany 73 - Electrostatic discharge

Support and other resources 75 Support and other resources Before you contact HP Be sure to have the following information available before you call

Strany 74 - Specifications

Support and other resources 76 providers or service partners) identifies that the repair can be accomplished by the use of a CSR part, HP will ship

Strany 75 - Support and other resources

Support and other resources 77 Pour plus d'informations sur le programme CSR de HP, contactez votre Mainteneur Agrée local. Pour plus d'in

Strany 76

Support and other resources 78 HINWEIS: Einige Teile sind nicht für Customer Self Repair ausgelegt. Um den Garantieanspruch des Kunden zu erfüllen,

Strany 77 - Customer Self Repair

Support and other resources 79 sustituciones que lleve a cabo el cliente, HP se hará cargo de todos los gastos de envío y devolución de componentes

Strany 78

Component identification 8 Drive LED definitions Item LED Status Definition 1 Locate Solid blue The drive is being identified by a host a

Strany 79 - Reparo feito pelo cliente

Support and other resources 80 Opcional – Peças cujo reparo feito pelo cliente é opcional. Essas peças também são projetadas para o reparo feito pel

Strany 80

Support and other resources 81

Strany 81

Support and other resources 82

Strany 82

Acronyms and abbreviations 83 Acronyms and abbreviations ABEND abnormal end ACU Array Configuration Utility ADM Advanced Data Mirroring AMP Advan

Strany 83 - Acronyms and abbreviations

Acronyms and abbreviations 84 PXE preboot execution environment RBSU ROM-Based Setup Utility RDIMM registered dual in-line memory module SAS seri

Strany 84

Documentation feedback 85 Documentation feedback HP is committed to providing documentation that meets your needs. To help us improve the documentat

Strany 85 - Documentation feedback

Index 86 A access panel 14 acoustics statement for Germany 71 ACU (Array Configuration Utility) 52, 60 Advanced ECC memory 38, 39, 59 Array

Strany 86 - Index 86

Index 87 FBWC capacitor pack 42, 48 FCC (Federal Communications Commission) notice 66, 67 FCC rating label 66 features 6, 60 Federal Communi

Strany 87 - Index 87

Index 88 memory, Advanced ECC 38, 59 memory, configuration requirements 37 memory, configuring 37, 38 memory, online spare 38, 59 mezzanine

Strany 88 - Index 88

Index 89 system maintenance switch 8, 9 system, keeping current 62 T T-15 Torx screwdriver 11 Taiwan battery recycling notice 71 technical s

Strany 89 - Index 89

Component identification 9 Item Description 1 Processor 2 DIMM slots 2 Processor 1 DIMM slots 3 Internal USB connector 4 Pass-thru board 5 TPM

Komentáře k této Příručce

Žádné komentáře