Hp RP7 Retail System Model 7100 Uživatelský manuál

HP Wireless Barcode ScannerUser Guide

Figure 1-16 Exit Global Suffix ModeFigure 1-17 Exit Programming ModeVolumeScan the following bar code to set the scanner back to the factory default

Figure 1-22 MediumFigure 1-23 HighScan the following barcode to exit the programming mode.Figure 1-24 Exit Programming ModeVolume 5

2 Product FeaturesHP Wireless Barcode ScannerWith rich feature sets and extensive model options, the HP Wireless Barcode Scanner represents thepremium

3 Safety and MaintenanceErgonomic RecommendationsWARNING! In order to avoid or minimize the potential risk of ergonomic injury follow therecommendatio

CleaningExterior surfaces and scan windows exposed to spills, smudges or debris require periodic cleaning toensure best performance during scanning op

4 Setting Up and Using the ScannerFollow the steps below to connect and get the scanner up and communicating with its host.1. Configure the Base Stati

NOTE: A tool such as a rigid pen or a flat screwdriver can be used to change the mounts. Do notallow it to touch the contacts.1. Insert the appropriat

3. The stand can now be repositioned in either horizontal (1) or standing (2) position.Figure 4-4 Repositioning the StandConnecting the Base StationY

Figure 4-5 Connecting the Base StationNOTE: The scanner can be set up to require a PIN code when connecting to the host. If you areadding new equipme

Using the BaseBase LEDsLEDs on the Base provide information about the Base as well as battery charging status, as shownbelow.Figure 4-7 Base LEDsNo.

© 2013 Hewlett-Packard DevelopmentCompany, L.P.Microsoft and Windows are eithertrademarks or registered trademarks ofMicrosoft Corporation in the Unit

Battery SafetyTo install, charge, and/or perform any other action on the battery, follow the instructions in thismanual.WARNING! Do not discharge the

other words, the batteries should be expected to take 500 full discharge/charge cycles beforeneeding replacement. This number is higher if partial dis

Replacing the BatteriesNOTE: Before proceeding, read “Battery Safety” on the preceding pages. HP recommends annualreplacement of rechargeable battery

3. Carefully lift out the gold contacts circuit (1), and remove the battery holder cap while letting thewhite connector pass through the hole (2) in t

Figure 4-12 Relative Size and Location of Aiming System PatternA red beam illuminates the label. The field of view indicated by the aiming system wil

Power OffScan the bar code below to shut off power to the BT handheld until the next trigger pull.Figure 4-15 Power OffSelecting the Interface TypeUp

Country ModeThis feature specifies the country/language supported by the keyboard. The following languages aresupported:U.S. English Norwegian KoreanU

5 Programming the ScannerThe scanner is factory-configured with a set of standard default features. After scanning the interfacebar code from the Inte

Reading ParametersMove the scanner toward the target and center the aiming pattern and illumination system to captureand decode the image. See Using t

6 Operating ModesScan ModeThe imager can be set to operate in one of several scanning modes. See the HP Wireless BarcodeScanner Programming Reference

About This GuideThis guide provides information on setting up and using the HP Wireless Barcode Scanner.WARNING! Text set off in this manner indicates

Figure 6-2 Scan Mode = Trigger SingleFigure 6-3 Scan Mode = Trigger Pulse MultipleFigure 6-4 Scan Mode = Trigger Hold MultipleFigure 6-5 Scan Mode

●Switch to Flashing - Automatically switches the scanner to Flash Mode when placed in thestand.●Switch to Always On - Automatically switches the scann

A Technical SupportOnline Technical SupportFor the online access to technical support information, self-solve tools, online assistance, communityforum

B Technical SpecificationsThe following table contains physical and performance characteristics, user environment andregulatory information.Item Descr

Depth of Field (Typical)1 Symbology SR:Code 39 5mil: 1.6” - 7.5” (4.0 - 19cm);10mil: 0.4” - 11.8” (1.0 - 30cm);20mil: up to 17.7” (up to 45cm)EAN 7.5m

Decode Capability 1D Bar Codes 2D / Stacked Codes The scanner is capable of decoding the following symbologies using multiple frames (i.e. Mul

LED and Beeper IndicationsThe scanner’s beeper sounds and its LED illuminates to indicate various functions or errors on thescanner. An optional “Gree

INDICATION DESCRIPTION LED BEEPERLabel Programming ModeAcceptance of Partial LabelIn cases where multiplelabels must be scanned toprogram one feature,

C Agency Regulatory NoticesIn some environments, the use of wireless devices may be restricted. Such restrictions may apply on-board airplanes, in hos

Houston, Texas 77269-2000Or, call 1-800-HP-INVENT (1-800 474-6836)For questions regarding this FCC declaration, contact:Hewlett Packard CompanyP. O. B

iv About This Guide

European Union Regulatory NoticeProducts bearing the CE marking comply with one or more of the following EU Directives as may beapplicable:Low Voltage

Product Environmental NoticesMaterials DisposalSome HP LCD monitors contain mercury in the fluorescent lamps that might require special handlingat end

Table of contents1 Quick Setup ...

Reading Parameters ... 22Aiming

1Quick SetupUse the bar codes in this chapter to perform quick setup procedures for common tasks. Scan thefollowing bar code to set the scanner back t

Carriage ReturnScan the following bar code to set the scanner back to the factory defaults.Figure 1-4 Set All DefaultsNOTE: Scanning the “Set All Def

Figure 1-10 Exit Programming ModeTabScan the following bar code to set the scanner back to the factory defaults.Figure 1-11 Set All DefaultsNOTE: Sc