HP Saw E4419B Uživatelský manuál Strana 168
- Strana / 204
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
HP4402.book : chapter4.fm 2 Fri Feb 12 15:32:45 1999
Error Messages
Introduction
4-2 HP E4419B User’s Guide
Introduction
This chapter contains information about the power meter’s error
messages. It explains how to read the power meter’s error queue and lists
all of the power meter’s error messages and their probable causes.
When there is a hardware related problem, for example, a power sensor
overload, the error message is displayed on the status line at the top of the
display. In addition, the errors are also written to the error queue. If there
are any errors in the error queue the front panel error annunciator is
displayed as shown in Figure 4-1.
Other errors can also be generated when the power meter is being
operated over the remote interface. These errors also display the error
annunciator and are written to the error queue.
Figure 4-1: Error Annunciator Position
To read the error queue from the front panel press:
• , , then use to scroll through
each error message.
To read the error queue from the remote interface use:
• the SYSTem:ERRor? command.
Error queue messages have the following format:
For example, -330, “Self-test Failed;Battery Fault”.
Error annunciator
System
Inputs
More
Error List Next
Error
,
“
”;
Device
Error
Description
Dependent InfoNumber
- User’s Guide 1
- Legal Information 3
- Limitation of Warranty 4
- Exclusive Remedies 4
- Equipment Operation 5
- General Safety Considerations 6
- IEC 1010-1 Compliance 7
- Statement of Compliance 7
- User Environment 7
- Installation Instructions 7
- Regulatory Information 8
- Declaration of Conformity 9
- List of Related Publications 10
- HP E4419B Options 11
- About this Guide 12
- Table of Contents 13
- .................... 2-27 14
- ........................ 2-29 14
- List of Figures 17
- List of Tables 19
- Getting Started 21
- Turning On the Power Meter 23
- The Front Panel at a Glance 24
- The Display Layout 27
- Selecting Your Display Layout 31
- Display Tutorial 32
- Window Symbols 34
- 1 of N Entry Window 35
- Numeric or Alphanumeric Entry 35
- The Rear Panel at a Glance 36
- Adjusting the Carrying Handle 38
- Rack Mounting the Power Meter 39
- General Information 43
- Running Time 43
- Charging Times 44
- Backlight 44
- Battery Removal/Replacement 45
- 2-6 HP E4419B User’s Guide 46
- Zeroing the Power Meter 47
- Zero/Cal Lockout 47
- Calibrating the Power Meter 48
- 2-12 HP E4419B User’s Guide 52
- 1 2 3 4 5 6 7 8 53
- HP E4419B User’s Guide 2-15 55
- Procedure 56
- Power Sensors 58
- Making the Measurement 62
- HP E4419B User’s Guide 2-27 67
- 2-28 HP E4419B User’s Guide 68
- HP E4419B User’s Guide 2-29 69
- Offset Tables 70
- Making Relative Measurements 77
- Setting the Resolution 78
- Setting Offsets 79
- Setting Averaging 81
- Step Detection 83
- Measuring Pulsed Signals 84
- Setting Measurement Limits 86
- Setting Window Limits 87
- Checking for Limit Failures 90
- Channel Measurements 92
- Making Ratio Measurements 94
- Setting the Range 98
- RS232/RS422 100
- Power Meter Operation 101
- Remote Interface Overview 102
- HP E4419B User’s Guide 2-63 103
- Recorder Outputs 105
- Leveling a Source Output 106
- 2-68 HP E4419B User’s Guide 108
- Presetting the Power Meter 110
- 2-72 HP E4419B User’s Guide 112
- • is set to “Off” 112
- TTL Inputs Off/On 112
- Self Test 113
- Remote Testing 116
- Test Descriptions 117
- Operator Maintenance 120
- Contacting Hewlett-Packard 121
- Check the Basics 122
- Instrument serial numbers 122
- GB12345678 123
- Sales and Service Offices 124
- 2-88 HP E4419B User’s Guide 128
- Menu Reference 129
- Introduction 130
- The Front Panel Menu Maps 131
- Frequency/Cal Fac Menu 132
- Meas Setup Menu 133
- Rel/Offset Menu 134
- Save/Recall Menu 134
- System Inputs Menu (1 of 4) 135
- System Inputs Menu (2 of 4) 136
- System Inputs Menu (3 of 4) 137
- System Inputs Menu (4 of 4) 138
- Zero/Cal Menu 139
- Front Panel Menu Reference 140
- Frequency 141
- More More 146
- Diagrammatical Hardkeys 164
- 3-38 HP E4419B User’s Guide 166
- Error Messages 167
- Specifications 179
- Power Meter Specifications 181
- Accuracy 182
- Power Reference 183
- Measurement Speed 184
- Zero Drift of Sensors 185
- Measurement Noise 185
- Settling Time 187
- Power Sensor Specifications 190
- General Characteristics 192
- Environmental Characteristics 193
- Dimensions 194
- Remote Programming 194
- Non-Volatile Memory 195
- 5-18 HP E4419B User’s Guide 196
- 3-19, 3-26 200
- , 1-8, 3-3 202
- "Zero/Cal" 203
Související produkty a manuály pro Měření, testování a kontrola HP Saw E4419B
(63 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce