HP 300-1020 Instalační manuál

Sun Internal ONLY!!The Sun-4 Handbook describes and illustrates the Sun-4 andSun-4e products for service providers who service these products after th

Brown PS41325 Watt Power SupplySun-4/110/310300-1022Sun4/II: Power - Brown PS41 325 Watt Power Supplyhttp://lios.apana.org.au/~cdewick/sunshack/data/f

Solaris 2.3 SCSI TargetsSolaris 2.3 allows any SCSI device to be assigned any Target number. This chart shows the defaulttarget numbers for sd and st

33 495 - 509 499 - 500 50134 510 - 524 514 - 515 51635 525 - 539 529 - 530 53136 540 - 554 544 - 545 54637 555 - 569 559 - 560 56138 570 - 584 574 - 5

Single-ended 8-bit SCSI PinoutsSIGNAL DD-50P HD-50 DD-50SA HD-68 SIGNAL DD-50P HD-50 DD-50SA HD-68-DB(0) 2 26 34 40 GND 1 1 1 6-DB(1) 4 27 2 41 GND 3

NotesOn HD50 cables, Pins 12, 14, 37, and 39 are reserved and Pin 13 is open.1. On HD50 to HD68 cables, Pins 1, 2, 3, 4, 5, 17, 18, 31, 32, 33, 34, 3

Media Defect ManagementEmbedded SCSI Disk DrivesThe FORMAT UNIT command formats the media so that all data blocks can be accessed. Thefollowing lists

SCSI Option BitSCSI Option Bit SettingUse the following procedure to determine the SCSI option bit setting under Solaris 2.x:# adb -k /kernel/unix /de

SCSI Sense KeysKEY DESCRIPTION0 NO SENSEThere is no specific sense key information to be reported for the designated logical unit. Thiswould be the ca

c HARDWARE ERRORThe target detected a non-recoverable hardware failure while performing the command orduring self test.d VOLUME OVERFLOWA buffered per

SCSI Sense CodesBYTE DESCRIPTION12--13Additional Sense Code (ASC)Additional Sense Code Qualifier (ASCQ)00 00 No additional sense information00 01 File

10 00 ID CRC or ECC error11 00 Unrecovered read error11 01 Read retries exhausted11 02 Error log too long to correct11 03 Multiple read errors11 04 Un

Fuse:7 Amps @ 250 VoltsNoteWait at least two minutes after power down or power outage before turning power ON to allowthe unit to reset.Last updated:

1d 00 Miscompare during verify operation1e 00 Recovered ID with ECC correction20 00 Invalid command operation code21 00 Logical block address out of r

3b 03 Tape or electronic vertical forms unit not ready3b 04 Slew failure3b 05 Paper jam3b 06 Failed to sense top of form3b 07 Failed to sense bottom o

55 00 System resource failure57 00 Unable to recover table-of-contents58 00 Generation does not exist59 00 Updated block read5a 00 Operator request or

1.3GB IPI Disk DrivePhysical and Logical GeometryThe 1.3GB IPI Disk Drive uses Zone Bit Recording (ZBR). The outer tracks have a higher bit densitytha

10 1601 1800 2007326 1513/13/74 2218125 1672/13/39 62 105411 1801 1900 2218126 1672/13/40 2320125 1749/12/15 60 102012 1901 2000 2320126 1749/12/16 24

To find the Physical SectorThe function of the Modulus Operator % is to give the remainder of the first value divided by thesecond value.Calculator Co

To find the Physical Head(Pcylinder remainder × Cylinder size) ÷ Track Size = Phead(0.54644 × 1292) ÷ 76 = Phead(706.00048) ÷ 76 = 9.289489 = Phead (0

ISP-80 Disk ControllerSelf-Test Error CodesLED 7 lights to indicate a failed self-testSun4/II: Trouble - Disk - SP-80 Disk Controller (IPI-2)http://li

Diagnostic Engineering MonitorThe Diagnostic Engineering Monitor (DEMON) is entered when the Diag/Norm switch is in the Diagposition.POSITION SYSTEM A

CPUSun-4 ArchitectureSun 4100Sun 4200Sun 4300Sun 4300 Address DecodingSun 4400Interrupt LevelsSun-4 / Sun-4c / Sun-4mLast updated: December 2, 1996Com

Fuji PEX391850 Watt Power SupplySun-4/260/280/360/380300-1024Sun4/II: Power - Fuji PEX391 850 Watt Power Supplyhttp://lios.apana.org.au/~cdewick/sunsh

Sun 4100Self-Test Error CodesSun4/II: Troubleshooting - CPU - Sun 4100 Self-Test Error Codeshttp://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wc

Last updated: December 2, 1996Comments and SuggestionsSun4/II: Troubleshooting - CPU - Sun 4100 Self-Test Error Codeshttp://lios.apana.org.au/~cdewick

Sun 4200Self-Test Error CodesSun4/II: Troubleshooting - CPU - Sun 4200 Self-Test Error Codeshttp://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wc

Last updated: December 2, 1996Comments and SuggestionsSun4/II: Troubleshooting - CPU - Sun 4200 Self-Test Error Codeshttp://lios.apana.org.au/~cdewick

Sun 4300Self-Test Error CodesSun4/II: Troubleshooting - CPU - Sun 4300 Self-Test Error Codeshttp://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wc

Last updated: December 2, 1996Comments and SuggestionsSun4/II: Troubleshooting - CPU - Sun 4300 Self-Test Error Codeshttp://lios.apana.org.au/~cdewick

Sun 4300 Address DecodingThe physical address and the byte in error are used to determine a failing SIMM module. Socketlocations are silkscreened on t

4-8MB 000000-7fffff 1 1 U1307Sun 4300 Address Decoding1st 3U Memory Board AddressingADDRESS (Dec) ADDRESS (Hex) BANK BYTE SOCKET8-12MB 800000-bfffff 0

36-40MB 2400000-27fffff 3 2 U170636-40MB 2400000-27fffff 3 3 U17071st 24 Mbytes of 9U Memory Board AddressingADDRESS (Dec) ADDRESS (Hex) BANK BYTE SOC

36-40MB 2400000-27fffff 3H 3 U190740-44MB 2800000-2bfffff 4L 0 U200040-44MB 2800000-2bfffff 4L 1 U200140-44MB 2800000-2bfffff 4L 2 U200240-44MB 280000

Fuse30 Amps @ 250 VoltsNoteThe Fuji 300-1024 is the same as the Fuji 300-1016.Last updated: December 2, 1996Comments and SuggestionsSun4/II: Power - F

Sun 4400Self-Test Error CodesSun4/II: Troubleshooting - CPU - Sun 4400 Self-Test Error Codeshttp://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wc

Last updated: December 2, 1996Comments and SuggestionsSun4/II: Troubleshooting - CPU - Sun 4400 Self-Test Error Codeshttp://lios.apana.org.au/~cdewick

Interrupt LevelsSPARC Sun-4 Sun-4c Sun-4mLevel 1 SW1 SW1 SW1Level 2 VME1 SBus2 SW2, VME1, SBus1Level 3 VME2 SBus3, SCSI SW3, VME2, SBus2Level 4 SW4, S

PrinterConnector PinoutsSBus Printer CardSPARCprinterPrintersLaserWriter IISPARCprinterLast updated: December 2, 1996Comments and SuggestionsSun4/II:

Connector PinoutsSBus Printer Card 501-1540 Video PortSBus Printer Card 501-1910 Video Port20-Pin to 25-Pin Cable 370-136520-Pin Hi-Density FemalePIN

Comments and SuggestionsSun4/II: Parts - Printer - Pinoutshttp://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00674.htm (2 von 2) [25.

Connector PinoutsSPARCprinter20-Pin to 25-Pin Cable 370-136525-Pin Female D-SubPIN SIGNAL PIN SIGNAL1 VCLK+ 14 VDATA+5 LSYNC+ 18 LSYNC-7 STATUS+ 20 LS

LaserWriter IILW-1 LW-2 LW-3115V LaserWriter 240V LaserWriter 115V LaserWriterA4 Paper TrayPART # DESCRIPTION365-1040370-1189370-1196536-1003350-10153

SPARCprinterOption SPRN-400Xerox 4030PART # DESCRIPTION365-1089 SPARCprinter (115V & 240V)365-1124 Toner Cartridge 1365-1125 Drum Cartridge 2365-1

SPARCprinter IOT Test PrintSwitch the printer OFF.1. Press and hold TEST.2. Switch the printer ON.3. Release TEST. 00 is displayed. The printer mus

Delta DPS-118AB120 Watt Power SupplyOptions 526 / 527 / 530 / 539 / 561 / 563 / 565Options 566 / RR126 / RR128 / RR129 / RREXP300-1031Fuses4 Amps @ 25

SPARCprinter Output Component TestsSwitch the printer OFF.1. Press and hold ENTER.2. Switch the printer ON.3. Press TEST until the desired diagnost

Configuration 7 xx 3Paper matrix 8 xx 4Console Type 9 xx 4Processing Direction controls the top and bottom page margin. Each increment from 0 to Fadju

MonitorMonitor and Image SizeConnector PinoutsCables12-inch Color LCD14-inch Color CRT14-inch Color Entry-Level CRT14-inch Monochrome LCD15-inch Color

Monitor and Image SizeMonitor size is the diagonal dimension of the CRT or the diagonal dimension of the CRT phosphorcoating.The image size of monitor

Connector PinoutsMonochrome CRT9-Pin Female D-SubPIN SIGNAL PIN SIGNAL1 VIDEO+ 6 VIDEO-2 GND 7 GND3 HSYNC 8 GND4 VSYNC 9 GND5 Not usedColor CRT DB13W3

7 Monitor specificColor CRT HD15 ConnectorPIN SIGNAL PIN SIGNAL1 Red 9 Not used2 Green 10 Sync Gnd3 Blue 11 Gnd4 Not used 12 DDC Data5 Not used 13 Hsy

Video CablesPART # DESCRIPTION530-0492 Color CRT Cable, 4.6M, 1xBNC to 1xBNC530-1138 Color CRT Cable, 4.6M, 4xBNC to 4xBNC530-1307 Color CRT Cable, 4.

12-inch Color LCDImage Size:239 mm Horizontal179 mm Vertical299 mm DiagonalPixelResolutionHorizontalFrequencyVerticalFrequencyDataClock1024 x 768 51.9

14-inch Color CRTImage Size:244 mm Horizontal183 mm Vertical305 mm DiagonalPixelResolutionHorizontalFrequencyVerticalFrequencyPixelFrequency1024 x 768

S2 is grounded. The Sense Code is 3.Last updated: December 2, 1996Comments and SuggestionsSun4/II: Parts - Monitor - 14-inch Color CRThttp://lios.apan

Last updated: December 2, 1996Comments and SuggestionsSun4/II: Power - Delta DPS-118AB 120 Watt Power Supplyhttp://lios.apana.org.au/~cdewick/sunshack

14-inch Entry-Level Color CRTImage Size:255 mm Horizontal191 mm Vertical319 mm DiagonalPixelResolutionHorizontalFrequencyVerticalFrequencyPixelFrequen

14-inch Monochrome LCDImage Size:274 mm Horizontal214 mm Vertical347 mm DiagonalPixelResolutionHorizontalFrequencyVerticalFrequencyDataClock1152 x 900

15-inch Color CRTImage Size:262 mm Horizontal200 mm Vertical329 mm DiagonalPixelResolutionHorizontalFrequencyVerticalFrequencyPixelFrequency1152 x 900

15-inch Color CRTImage Size:260 mm Horizontal195 mm Vertical325 mm DiagonalPixelResolutionHorizontalFrequencyVerticalFrequencyPixelFrequency1152 x 900

15-inch Monochrome CRTImage Size:250 mm Horizontal187 mm Vertical312 mm DiagonalPixelResolutionHorizontalFrequencyVerticalFrequencyPixelFrequency1024

16-inch Color CRTImage Size:295 mm Horizontal230 mm Vertical374 mm DiagonalPixelResolutionHorizontalFrequencyVerticalFrequencyPixelFrequency1152 x 900

Philips/Fimi C1764SPARCstation IPC Option LPC365-1143 115V Monitor, DB13W3, FCC-B/VCCI-2Philips/Fimi C1764SPARCstation IPC Option LPC365-1146 240V Mon

16-inch Premium Color CRTImage Size:295 mm Horizontal230 mm Vertical374 mm DiagonalPixelResolutionHorizontalFrequencyVerticalFrequencyPixelFrequency94

P4 CG6, 501-1532-09 and belowSBus CG6, 501-1481-04 and belowSBus CG6 501-1645-03 and below.Last updated: December 2, 1996Comments and SuggestionsSun4/

16-inch Mid-Range Color CRTImage Size:95 mm Horizontal226 mm Vertical371 mm DiagonalPixelResolutionHorizontalFrequencyVerticalFrequencyPixelFrequency1

Boschert XL520-3625520 Watt Power SupplySun-4/330300-1034Sun4/II: Power - Boschert XL520-3625 520 Watt Power Supplyhttp://lios.apana.org.au/~cdewick/s

70MHz >=501-3002-02 Yes85MHz >=501-2549-03 Yes85MHz >=501-2928-02 Yes110MHz >=501-3008-03 Yes110MHz 501-3109-xx Yes 2110MHz 501-3134-xx Ye

17-inch Premium Color CRTImage Size:300 mm Horizontal234 mm Vertical380 mm DiagonalPixelResolutionHorizontalFrequencyVerticalFrequencyPixelFrequency11

17-inch Premium Color CRTImage Size:300 mm Horizontal225 mm Vertical375 mm DiagonalImage Size:293 mm Horizontal234 mm Vertical375 mm DiagonalPART # DE

17-inch Entry-Level Color CRTImage Size:300 mm Horizontal225 mm Vertical375 mm DiagonalPixelResolutionHorizontalFrequencyVerticalFrequencyPixelFrequen

85MHz >=501-2928-02 Yes110MHz >=501-3008-03 Yes110MHz 501-3109-xx Yes 2110MHz 501-3134-xx Yes 2NotesIf the SPARCstation 4 tcx frame buffer outpu

17-inch Greyscale CRTImage Size:295 mm Horizontal230 mm Vertical374 mm DiagonalPixelResolutionHorizontalFrequencyVerticalFrequencyPixelFrequency1152 x

365-1157Zenith 17SMM4-A115V/240V Monitor, DB13W3, FCC-B/VCCI-2,with Video Cable 530-1870* The Mode III (1024 x 800 @ 84) Overscan Mode user area is 91

19-inch Color CRTImage Size:255 mm Horizontal280 mm Vertical452 mm DiagonalPixelResolutionHorizontalFrequencyVerticalFrequencyPixelFrequency1152 x 900

365-1039150-1226180-1125Sony P2 GDM-1955A40, .31 mm Dot-Pitch240V Monitor, 4xBNCFuse, 3.15APower Cord, IEC 320/CEE 22 to pigtail365-1065150-1225Sony P

19-inch Premium Color CRTImage Size:350 mm Horizontal270 mm Vertical442 mm DiagonalPixelResolutionHorizontalFrequencyVerticalFrequencyPixelFrequency10

FusesF1 = 20 Amps @ 250 voltsF2 = 10 Amps @ 250 voltsLast updated: December 2, 1996Comments and SuggestionsSun4/II: Power - Boschert XL520-3625 520 Wa

Comments and SuggestionsSun4/II: Parts - Monitor - 19-inch Premium Color CRThttp://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00661.

19-inch Greyscale CRTImage Size:350 mm Horizontal273 mm Vertical443 mm DiagonalPixelResolutionHorizontalFrequencyVerticalFrequencyPixelFrequency1152 x

1152 x 9001076 x 82471.7KHz71.7KHz76Hz76Hz105.5Mhz105.5MHz *PART # DESCRIPTION365-1099Philips M20P110A/710320115V/240V Monitor, DB13W3, FCC-B/VCCI-236

19-inch Greyscale CRT with OCLIImage Size:350 mm Horizontal273 mm Vertical443 mm DiagonalPixelResolutionHorizontalFrequencyVerticalFrequencyPixelFrequ

19-inch Monochrome CRTImage Size:350 mm Horizontal273 mm Vertical443 mm DiagonalPixelResolutionHorizontalFrequencyVerticalFrequencyPixelFrequency1152

365-1014150-1051150-1215180-1125Elston DM60-19A0-09-A104240V Monitor, DB9, 395x535 mm BaseFusecarrierFuse, 1.6APower Cord, IEC 320/CEE 22 to pigtail36

19-inch Monochrome CRT with OCLIImage Size:350 mm Horizontal273 mm Vertical443 mm DiagonalPixelResolutionHorizontalFrequencyVerticalFrequencyPixelFreq

19-inch Hi-Resolution CRTImage Size:355 mm Horizontal279 mm Vertical452 mm DiagonalPixelResolutionHorizontalFrequencyVerticalFrequencyPixelFrequency16

19-inch Hi-Resolution CRT with OCLIImage Size:355 mm Horizontal279 mm Vertical452 mm DiagonalPixelResolutionHorizontalFrequencyVerticalFrequencyPixelF

20-inch Premium Color CRTImage Size:350 mm Horizontal270 mm Vertical442 mm DiagonalPixelResolutionHorizontalFrequencyVerticalFrequencyPixelFrequency10

Seagate 45070622205 Watt Power SupplySeagate 97209-12G Disk DriveOptions 706 / 707 / 709 / 710300-1041FuseSoldered at F 100, 8 Amps @ 250 VoltsSun4/II

2 RS232 data in 9 Sense03 Sense2 10 Cgnd4 Sgnd A1 Red5 Csync A2 Green6 RS232 data out A3 BlueS0 and S1 are grounded. The Sense Code is 4.Pin-7 is not

6 SDA serial data I/O A3 Blue7 VsyncS0 and S1 are grounded. The Sense Code is 4.Pin-5 is Hsync if Vsync is present on Pin-7.Last updated: December 2,

20-inch Premium Greyscale CRTImage Size:350 mm Horizontal273 mm Vertical443 mm DiagonalPixelResolutionHorizontalFrequencyVerticalFrequencyPixelFrequen

Input DeviceSunButtonsSunDialsType-3 KeyboardType-3 Optical MouseType-3 to Type-4 Spares KitType-4 KeyboardType-5 KeyboardType-5c KeyboardType 101A Ke

SunButtonsOption 180Wiring DiagramCODE PART # DESCRIPTION- 595-1865 230V SunButtons Assembly- 595-1884 115V SunButtons Assembly1 300-1053 115V Power S

Comments and SuggestionsSun4/II: Parts - Input Device - SunButtonshttp://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00634.htm (2 von

SunDialsOption 190Wiring DiagramPART # DESCRIPTION- 595-1737 115V SunDials Assembly- 595-1773 230V SunDials Assembly1 300-1053 115V Power Supply2 300-

Comments and SuggestionsSun4/II: Parts - Input Device - SunDialshttp://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00635.htm (2 von 2

Type-3 KeyboardPART # DESCRIPTION370-1063 Type-3 Keyboard, DB-15 (obsolete)370-1095 Type-3 Keyboard, DB-15530-1526 Type-3 Keyboard Adapter Cable, DB-1

Type-3 Optical MousePART # DESCRIPTION370-1058370-1091M3 Mouse and Pad, RJ11 (obsolete)M3 Mouse and Pad, RJ11 (obsolete)365-1042370-1169370-1171370-12

Notes205 Watt Power Supply 300-1041Supports one Seagate 97209-12G 3MB/Sec IPI Disk Drive.Does NOT Support the Seagate 97229-11G 6MB/Sec IPI Disk Drive

Type-3 to Type-4 Spares KitPART # DESCRIPTION560-1501320-1005370-1170370-1368530-1443530-1479Type 3 Keyboard/Mouse to Type 4 Keyboard/Mouse KitType-4

Type-4 KeyboardUnderside of KeyboardDESCRIPTIONDIP SWITCHCODE1 2 3 4 5 6 7 8Sun-3/4 w >=4.0 or 386i Off - - - - - - - -Sun-3 w <=3.5 On - - - -

320-1007 Type-4 Keyboard, Mini-Din, Swiss German320-1008 Type-4 Keyboard, Mini-Din, Belgium and France320-1009 Type-4 Keyboard, Mini-Din, UK320-1010 T

Type-5 KeyboardUnderside of KeyboardDESCRIPTIONDIP SWITCHCODE1 2 3 4 5 6 7 8US - - On - - - - On 21US/Unix - - On - - - On - 22French - - On - - - On

320-1075 Type-5 Keyboard, Mini-Din, Danish320-1076 Type-5 Keyboard, Mini-Din, German320-1077 Type-5 Keyboard, Mini-Din, Italian320-1078 Type-5 Keyboar

Type-5c KeyboardDESCRIPTIONWIRE JUMPERHEXCODEJS1 JS2 JS3 JS4 JS5US - - - - In 21US/Unix - - - In - 22Japanese In - - - In 31DESCRIPTIONDIP SWITCHHEXCO

320-1234 Type-5c Keyboard, 2M Cable, Mini-Din, US/UNIX320-1252 Type-5c Keyboard, 2M Cable, Mini-Din, French320-1236 Type-5c Keyboard, 2M Cable, Mini-D

Type-101A KeyboardUnderside of KeyboardPART # DESCRIPTION320-1070 Type 101A Keyboard, Mini-Din530-1442 Keyboard Cable, Mini-Din to Mini Din, 2.0M530-1

Type-4 Optical MousePART # DESCRIPTION370-1161365-1059370-1170370-1215370-1368M4 200 CPI Mouse and Pad, Mini-Din (unreleased, obs)M4 200 CPI Mouse and

Type-5 Optical MousePART # DESCRIPTIONf370-1398370-1398370-1399370-1664370-1663Type-5 Mouse and Pad, Mini-DinType-5 Mouse, 300 CPI, Mini-DinType-5 Mou

[ Configurations ] [ CPU ] [ Memory ] [ Graphics ] [ IPI ] [ SCSI ] [ SCSI Disk ][ Removable Media ] [ Communication ] [ Miscellaneous

Fuji PEX479-30925 Watt Power SupplySun-4/260/280/360/380300-1043Sun4/II: Power - Fuji PEX479-30 925 Watt Power Supplyhttp://lios.apana.org.au/~cdewick

BoardIDPROMBoot PROM Sun-4 ArchitectureCPU Sun-4 ArchitectureMemory Sun-4 SIMMs / Sun-4c SIMMsVideo P4 Bus VMEbus CablesSCSI Multibus / VMEbus Single-

IDPROMThe IDPROM address space provides system information including Machine Type, Serial Number,Ethernet Address, and Manufacturing Date. This inform

NVRAM Component TypesNVRAM Battery TypesARCH SYSTEM HOSTID COMPONENT TYPE PART # SOCKETSun4/II: Parts - Board - IDPROMhttp://lios.apana.org.au/~cdewic

Sun-44/260/2804/110/1504/3xx4/3xx4/470/4904/470/4902100xxxx22xxxxxx23xxxxxxNone24xxxxxxNoneIDPROMIDPROMIDPROM48T02 NVRAMIDPROM48T02 NVRAM520-1532520-1

Boot PROMSun-4 ArchitectureSun-4100 / Sun-4200 / Sun-4300Sun-4/110/150U601 U602 U603 U604 Revision520-1651-03 520-1652-03 520-1653-03 520-1654-03 1.35

Sun-4/470/490U3504 U3503 U3502 U3501 Revision525-1103-01 525-1104-01 525-1105-01 525-1106-01 0.1.d525-1103-02 525-1104-02 525-1105-02 525-1106-02 0.2.

CPUSun-4 ArchitectureSun 4100 / Sun 4200 / Sun 4300 / Sun 4400PART # DESCRIPTION501-1199 8MB Sun 4100 CPU (270-1199-03) without FPC501-1512 8MB Sun 41

Comments and SuggestionsSun4/II: Parts - Board - CPU Sun-4http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0060c.htm (2 von 2) [25.

MemorySun-4 SIMMsPART # DESCRIPTION501-1314 256KB, 256KB x 9-Bit SIMM, Sun 4100501-1544 1MB, 1Mbit x 9-Bit SIMM, Sun 4300501-1408 1MB, 1Mbit x 9-Bit S

VideoP4 BusPART # DESCRIPTION501-1247 MG3 ECL Frame Buffer, DB-9501-1248 CG4 Color Frame Buffer, BNC501-1371 CG8 Color Frame Buffer, BNC501-1402 MG4 E

FuseLittelfuse 30A 250V BLN 30NoteUse wire harnesses 530-1578 and 530-1580 for the 80/280/380/480 chassis. Use wire harnesses530-1578 and 530-1581 for

VideoVMEbusPART # DESCRIPTION501-1014 CG2 Color Frame Buffer540-1126 CG2 Color Frame Buffer (obsolete)599-1165 CG2 Color Frame Buffer (obsolete)501-10

VideoCablesPART # DESCRIPTION530-0492 Color Cable, 4.6M, 1xBNC to 1xBNC530-1138 Color Cable, 4.6M, 4xBNC to 4xBNC530-1307 Color Cable, 4.6M, 4xBNC to

SCSIMultibus / VMEbusPART # DESCRIPTION501-1006 Sun-2 Multibus SCSI Host Adapter501-1045 Sun-2 VMEbus SCSI Host Adapter501-1120 Sun-3 VMEbus SCSI Host

SCSISingle-Ended 8-Bit SCSI CablesPART # DESCRIPTION530-1185 External Cable, DD-50SA to DD-50SA, Ribbon, 1.0M (obs)530-1186 External Cable, DD-50SA to

IPIISP-80PART # DESCRIPTION501-1539501-1855530-1487530-1488530-1489530-1518530-1536530-1788530-1789ISP-80 IPI-2 DIsk ControllerISP-80 IPI-2 DIsk Contr

CommunicationEthernet AccessoriesPART # DESCRIPTION130-1240 BNC Female to N-series Male Option TA-M130-1241 BNC Male Terminator Option TT-M130-1242 BN

370-1071370-1072530-1241530-1254Option INLINE3Com 3C106 TransceiverVampire Tap Block, AMP 228752-115-meter Transceiver Drop Cable15-meter Ethernet Coa

CommunicationVMEbusEthernet / FDDI / Network CoProcessorPART # DESCRIPTION501-8027 Sun-3/E SCSI/Ethernet Controller501-1153501-1004530-1173Sun-2 Ether

501-1203530-1312530-1315340-1569340-1587340-1914340-1915530-1334540-1526540-1558540-156016-Channel Asychronous Line Multiplexer-2 (ALM-2)Internal Para

Backplanes and I/O BoardsPART # DESCRIPTION501-1092 12-Slot VMEbus Backplane, (obsolete)501-1117 12-Slot VMEbus Backplane, Pressfit501-1127 3-Slot VME

Boschert XL121-3630130 Watt Power SupplyOptions 501 / 503 / 504 / 505 / 506 / 507Options 509 / 510 / 511 / 514 / 516300-1045Sun4/II: Power - Boschert

MiscellaneousBoardsPART # DESCRIPTION501-1154 VMEbus to Multibus Adapter Assembly, Blank Backpanel501-1191 VME 3x2 Adapter Assembly, without P2 A&

MiscellaneousBoard HardwarePART # DESCRIPTION130-0272 2-Pin Shunt, 0.10" Pin Spacing, 0.025" Pin Diameter130-2190 2-Pin Shunt, 2.0 mm Pin Sp

Miscellaneous OptionsOption 955 56-inch Expansion CabinetOption 960 76-inch Expansion CabinetLast updated: December 2, 1996Comments and SuggestionsSun

95556-inch Expansion CabinetCODE PART # DESCRIPTION1 340-1884 Anti-Tilt Panel2 540-1857 Vented Panel AssemblySun4/II: Parts - Miscellaneous Options -

3 540-1947 1/2" Tape Panel Assembly with Cutout4 540-2252 Front Panel with 4 Tape Drive Cutouts5 540-1859 Cap Panel Assembly6 240-1630 #6-32 Ball

96076-inch Expansion CabinetPART # DESCRIPTION180-1149 32Amp IEC-309 AC Receptacle (240V)300-1011 AC Power Sequencer (115V)300-1263 AC Power Sequencer

530-1344 AC Power Cord, Fan Assembly (240V)530-1346 AC Power Cord, Fujitsu M2444AC Tape Drive (240V)530-1347 AC Power Cord, Fujitsu M2361A Disk Drive

Removable Media OptionsOptions 558 / 559 Desktop SunCD PackOption 660 150MB Tape Desktop Backup PackOptions 680 / 682 / 683 / 684 / 685 Front-Load 1/2

558 559SunCD CD-ROM SunCD CD-ROMDesktop SunCD PackCODE PART # DESCRIPTION1 540-1778 Cover Assembly, Tape and CD-ROM2334NSNS540-1978150-1557150-2049540

56540-1773330-1214Base AssemblyRubber Foot777300-1037300-1090300-110535 Watt Power Supply (obsolete) 135 Watt Power Supply (obsolete)44 Watt Power Sup

Fuse5 Amps @ 250 VoltsNoteUse Power Harness, 530-1432-01, for this power supply.Last updated: December 2, 1996Comments and SuggestionsSun4/II: Power -

660150MB TapeDesktop Backup PackCODE PART # DESCRIPTION1 540-1778 Tape Drive Cover Assembly234NS540-1776150-1338540-1802150-1174Fan/SCSI Connector/Add

2334NSNS540-1978150-1557150-2049540-1802150-1174340-2839Fan/SCSI Connector/Address Select AssemblyAddress Select Switch (obsolete)Address Select Switc

680 682 683 684 685TableTop 56" Rack56" Exp Rack1st Tape56" Exp Rack2nd TapeSC200056" Exp RackCODE SUN PART# HP PART# DESCRIPTION1

10 811-1235 3110-0178 Cover Hinge11 811-1231 1390-0776 Cover Latch12 811-1215 07980-60041 Speed Sensor Assembly13 811-1218 07980-60052 Takeup Hub Asse

COD E SUN PART# HP PART# DESCRIPTION25 811-1230 07980-86500 Blower Motor26 811-1217 07980-60050 Takeup/Supply Reel Motor27 811-1226 07980-60144 Hub Lo

NS 811-1243 88780-60082 Firmware Kit (not qualified)NS 811-1243 88780-6018 2 Firmware Kit 1NS 811-1244 07980-60048 NRZI Speed SensorFirmware Kit 88780

530-1501 Data Cable, DD-50SA to Centronics, 2.0M540-1823 Rackmount Tape Drive without Fuse and LabelsLast updated: December 2, 1996Comments and Sugges

Disk OptionsOptions 526 / 527 / 530 / 539 327MB Disk External Storage ModuleOptions 561 / 563 / 565 / 566 669MB Disk External Storage ModuleOptions 70

526 527 530 539327MB Disk 327MB Disk Expansion Two 327MB Disks327MB Disk150MB TapeExternal Storage and ExternalExpansion ModulesPART # DESCRIPTION150-

Last updated: December 2, 1996Comments and SuggestionsSun4/II: Parts - Disk Options - External Storage and External Expansion Moduleshttp://lios.apana

Zytec 22903110925 Watt Power SupplySun-4/370/470Options 509 / 510 / 511 / 514 / 516300-1047DC OUTPUT REGULATION FULL LOAD+5 150 Amps 145.0 Amps-5.2 15

561 563 565 566669MB Disk Two 669MB Disks669MB Disks150MB Tape669MB Disk2.3GB TapeExternal Storage and ExternalExpansion ModulePART # DESCRIPTION150-1

530-1659 Address Select Switch Cable, 2.54 mm Pin Spacing570-1042 Full-Height Peripheral Front Filler Panel814-5036 Replacing Components of Sun ESM an

706 707 709 7101.2GB Disk 2.1.2GB Disks 4 1.2GB Disks 8 1.2GB Disks1.2GB IPI-2 Disk SubsystemCODE PART # DESCRIPTION540-1770 IPI Drive, Power Supply,

8 370-1350 Air Baffle9 370-1187 1.2GB Disk, Seagate 97209-12G, PA8R210 240-1185 #6-32 x 1/4" Screw (use 7/64" Hex Screwdriver)11 250-1013 Gr

716 717 719 720911MB Disk 2 911MB Disks 4 911MB Disks 8 911MB Disks911MB IPI-2 Disk SubsystemCODE PART # DESCRIPTION540-2005 IPI Drive, Power Supply,

8 370-1350 Air Baffle9 370-1351 911MB Disk, Seagate 97229-11G, PA8Y210 240-1185 #6-32 x 1/4" Screw (use 7/64" Hex Screwdriver)11 250-1013 Gr

726 727 7282 1.3GB Disks1 Tray4 1.3GB Disks1 Tray1.3GB Disk1.3GB IPI-2 Disk SubsystemCODE PART # DESCRIPTION1 340-2461 Chassis Enclosure2 None #8-32 x

11 540-2125 3-Fan Tray Assembly, 45 CFM12 530-1764 DC Wire Harness13 540-2126 DC Fan Assembly, 45 CFM14 300-1085 268 Watt Power Supply14 300-1096 269

741A 742A 743A 745A 744A1.2GB Disk 2 1.2GB Disks 3 1.2GB Disks 4 1.2GB Disks1.2 GB DiskStandaloneSun Expansion PedestalCODE PART # DESCRIPTIONNSNS340-

NS 540-1847 Rear Bezel AssemblyNS 540-1939 Front Panel and Bumper AssemblyNS 530-1487 IPI Drive I/O Cable, 8.0M (obsolete)NS 530-1488 IPI Drive I/O Ca

+12 motor 15 Amps 6.3 Amps-12 10 Amps 4.0 AmpsLast updated: December 2, 1996Comments and SuggestionsSun4/II: Power - Zytec 22903110 925 Watt Power Sup

741L 742L 743L 744L 745L911MB Disk 2 911MB Disks 3 911MB Disks 4 911MB Disks 911MB DiskStandaloneSun Expansion PedestalCODE PART # DESCRIPTIONNSNS340-

NS 540-1847 Rear Bezel AssemblyNS 540-1939 Front Panel and Bumper AssemblyNS 530-1487 IPI Drive I/O Cable, 8.0MNS 530-1488 IPI Drive I/O Cable, 1.0MNS

750 754 7562 1.3GB Disks1 Tray4 1.3GB Disks8 mm Tape2 1.3GB DisksExpansion TraySCSI Expansion PedestalCODE PART # DESCRIPTION1 540-1846 Side Cover2 30

6 330-1192 Blank Bezel Insert7 330-1210 Front Bezel Half-Height Insert7 330-1284 Front Bezel Full-Height Insert8NSNS540-1939240-0558240-0557Front Beze

SystemSun-4 ArchitectureSun-4/110/310Sun-4/150/350Sun-4/260/360Sun-4/280/380Sun-4/330Sun-4/370/470Sun-4/390/490Last updated: December 2, 1996Comments

Sun-4/110/3103-Slot VMEbus Logic EnclosurePART # DESCRIPTION140-1019 Fuse, 15A (115V)140-1030 Fuse, 6.3A (240V)150-1042 Fusecarrier (115V)150-1051 Fus

Sun-4/150/3506-Slot VMEbus Logic EnclosurePART # DESCRIPTION140-1019 Fuse, 15A (115V)140-1030 Fuse, 6.3A (240V)150-1042 Fusecarrier (115V)150-1051 Fus

Sun-4/260/36012-Slot VMEbus Logic EnclosurePART # DESCRIPTION140-1019 Fuse, 15A (115V)140-1030 Fuse, 6.3A (240V)150-1018 AC Power Switch, Illuminated

540-1555540-1510530-13576-Fan Tray Assembly (obsolete)DC Fan Assembly, 71 CFMDC Harness, Fan Tray540-1581540-1510530-13576-Fan Tray Assembly, Low Prof

370-1010370-1034370-1034530-1134530-1135530-1142530-1145530-1157Adaptec ACB-4000 SCSI Disk Controller71MB Disk Drive, Micropolis 132571MB Disk Drive,

Fuji PEX527-30820 Watt Power SupplyOptions 733 / 734300-1052Sun4/II: Power - Fuji PEX527-30 820 Watt Power Supplyhttp://lios.apana.org.au/~cdewick/sun

Sun-4/280/38012-Slot VMEbus Logic EnclosurePART # DESCRIPTION140-1019 Fuse, 15A (115V)140-1026 Fuse, 6A (230V)140-1030 Fuse, 6.3A (240V)150-1018 AC Po

Power SuppliesPART # DESCRIPTION300-1024530-1206530-1340530-1222530-1320850 Watt Power Supply, Fuji ElectrochemicalDC Harness, +5Vdc (obsolete)DC Harn

340-1287 Panel, 24.5" x 19"340-1441 Keyswitch Panel, 1.5" x 19"340-1442 Tape Drive Filler Panel, 1.5" x 19"340-1485 19&q

340-1491 Fan Bracket370-1124 AC Fan (240V)540-1585 19" Logic Enclosure Support Rail Assembly340-1583 19" Logic Enclosure Support Rail Bracke

Sun-4/3305-Slot VMEbus Logic EnclosureCODE PART # DESCRIPTIONNS 260-3617 SPARCstation 330 LogoNS 260-3818 SPARCserver 330 Logo1 330-1178 Rear CoverNS

6NSNSNS340-1772501-1432501-1416120-1608SCSI Terminator Access PanelSCSI IN Terminator PCBSCSI OUT Terminator PCB220/330 Terminator7 540-1789 Top Cover

Wire harness 530-1469 is not field repairable or replaceable.2. The 1.3GB SCSI Disk does not fit into Tray 540-1757 or 540-1758.3. Last updated: Dec

Sun-4/370/47012-Slot VMEbus Logic EnclosureFront ViewRear ViewSun4/II: Parts - System - Sun-4/370/470http://lios.apana.org.au/~cdewick/sunshack/data/f

CODE PART # DESCRIPTION1 501-1439 12-Slot Backplane, Pressfit (obsolete) 11 501-1598 12-Slot Backplane, Pressfit1 501-1832 12-Slot Backplane, Pressfit

11NSNSNSNSNS540-1751530-1482540-1732530-1640370-1732370-1214Fan Tray Assembly, 9 Fans 2Fan Tray DC Harness for Fan 540-1732DC Fan Assembly, 150 CFMFan

Fuse20 Amps @ 250 VoltsNotes820 Watt Power Supply 300-1052-02Supports four CDC 9720-688 Disk Drives.Supports four Fujitsu M2372K Disk Drives.820 Watt

12-Slot VMEbus Logic Enclosure - ContinuedCODE PART # DESCRIPTIONNS 260-3719 Sun-4/370 LogoNS 340-1878 Rear Bezel (obsolete)NS 540-1848 Rear BezelNS 5

22 530-1500 Internal SCSI Bus Cable, 1.2M 223 370-1206 150MB Tape Drive, Full-Height, QIC-15023 370-1247 45/60MB Tape with MT02, Full-Height, QIC-11/2

CODE PART # DESCRIPTION1 501-1832 12-Slot Backplane, Pressfit with DC Harness Cutout2 540-1846 Side Cover3 300-1089 925 Watt Power Supply4 340-1898 To

10NSNSNS540-1751370-1214530-1640370-1732Fan Tray Assembly, 9 Fans 1DC Fan Assembly with Connector, 150 CFMFan Tray DC Harness for Fan 370-1732DC Fan A

Sun-4/390/490SCSI Peripheral TraysCODE PART # DESCRIPTIONSun4/II: Parts - System - Sun-4/390/490http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.

123456540-1865340-2000530-1474240-1202530-1507340-1832340-1999SCSI Tray, Versions 1 and 2 (Shipped before 4/90)SCSI TraySCSI Bus Cable, 73 cm, Interna

CODE PART # DESCRIPTION1 540-1719540-1840530-1560530-1561150-1393240-1614Blower Assembly, 2 BlowersCentrifugal Fan AssemblyCable, 32.5 cm, Fan to Term

4 150-1397 Indicator LED5 530-1506 Indicator LED Cable6 300-1065 1200 Watt Power Supply6 300-1047 925 Watt Power Supply (obsolete)7 501-1498 16-slot B

CODE PART # DESCRIPTION1 340-1884 Anti-Tilt Panel2 540-1857 Vented Panel Assembly3 540-1858 Upper Panel Assembly, 1/2" and 1/4" Tape, Hinged

8 540-1718 Frame Assembly9 540-2393 Keyswitch Assembly (replaced 540-1285)10 340-1881 Hinge Bracket11 340-1848 Side Panel12 340-1886 Side Restraint Br

Fuji PEX527-40410 Watt Power SupplyOptions 731 / 732300-1056Sun4/II: Power - Fuji PEX527-40 410 Watt Power Supplyhttp://lios.apana.org.au/~cdewick/sun

Parts BreakdownThis section contains illustrations, part numbers, and descriptions of Sun Systems, Options, Boards,Input Devices, Monitors, and Printe

370-xxxx-xx OEM Part500-xxxx-xx Untested PCB501-xxxx-xx Tested PCB520-xxxx-xx Programmed IC525-xxxx-xx Programmed IC530-xxxx-xx Cable540-xxxx-xx Assem

Higher/Lower Base Number ExamplesPART # DESCRIPTION RELEASE DATE300-1281300-1286SC2000 Power SupplySC2000 Power Supply3/28/959/19/94501-2925501-294050

R Japan (used by Fuji Xerox)T Milpitas, California (Re-Manufacturing)ToolsPART # DESCRIPTION250-1028 Field Engineer Toolkit (Jensen JTK-679-1)250-1024

250-1059 4.5 mm Nutdriver Blade250-1060 5 mm Nutdriver Blade250-1061 5.5 mm Nutdriver Blade250-1062 6 mm Nutdriver Blade250-1063 7 mm Nutdriver Blade2

250-1072 1/2" x 1/2" Thin-Head Wrench for 56" Rack Levelers250-1074 10-Inch End Cutter250-1088 Sun ESD Mat with Sun Logo330-1145 Dispos

Slot AssignmentBoard Installation NotesVMEbus Bus Grant and Interrupt AcknowledgeSCSI Host Adapter AssembliesSun-4 ArchitectureSun-4/110Sun-4/150Sun-4

Board Installation NotesBackplane Slot Assignment ChartsEach system chart lists the PCB slot assignments in order of descending priority. In the chart

Sun 4400 CPUThe Sun 4400 CPU requires 12-slot Backplane 501-1598 or 501-1382. The Sun 4400 CPU isnot supported in the 501-1439 12-slot Backplane.1. T

CG9 with GP2The CG9 P2 bus must be enabled (SW3-1, OFF).1. The CG9 must be installed in cardcage slots that share the P2 bus with the GP2.2. This co

Fuse20 Amps @ 250 VoltsNotes410 Watt Power Supply 300-1056-02Supports two CDC 9720-688 Disk Drives.Supports two Fujitsu M2372K Disk Drives.410 Watt Po

BOARDALM-1VECTORALM-2 & MCPVECTOR123456780x880x890x8a0x8b----0x8b0x8a0x890x880xa00xa10xa20xa3ALM-1 501-1157 (Pedestal Systems)The ALM-1 must be in

SBus Expansion Subsystem BoardThe SBus Expansion Subsystem Board does not use the VMEbus.Systech MTI-800, MTI-850, MTI-1600, and MTI-1650Tables A and

Comments and SuggestionsSun4/I: Slot Assignment - Board Installation Noteshttp://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005f3.ht

VMEbus Bus Grant and InterruptAcknowledgeThis chart shows how the Bus Grant In/Out and Interrupt Acknowledge In/Out signals are connectedon the board.

Comments and SuggestionsSun4/I: Slot Assignment - VMEbus Bus Grant and Interrupt Acknowledgehttp://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wc

SCSI Host Adapter AssembliesUse the slot assignment charts for systems with the 501-1138 or 501-1217 SCSI Assembly ifthere is no SCSI Host Adapter ins

Memory Boards With SCSIASSY # MEMORY BD # DESCRIPTION SCSI HOST501-1147 501-1079 2/50 0MB 501-1045501-1172 501-1121 3/75 0MB 501-1045Memory Boards Tha

Sun-4/110SHUNTSBOARDSLOT POSITIONBG3 IACK 1 2 3Out OutSun 4100 CPU (1)A AIn Out MCP AIn Out ALM-2 AIn OutColor (2)AIn Out HSI AOut Out Ethernet AOut O

Footnotes to Slot Assignments forSun-4/110/150/260/280NOTE # PART # BOARD1501-1199501-1237501-1462501-1463501-1464501-1465Sun 4100 CPU (-03 FAB) 8MB w

NOTE # PART # BOARD5501-1383501-1447TAAC-1 Application AcceleratorTAAC-1 Application AcceleratorNOTE # PART # BOARD6501-1102501-1451501-1254501-15768M

DC PowerPower Supplies 300-1020 -- Brown -- 575 Watts 300-1020 -- Fuji -- 575 Watts 300-1022 -- Summit -- 325 Watts 300-1022 -- Brown -- 325 Watts 300

Zytec 229074001200 Watt Power SupplySun-4/390/490SS690300-1065DC OUTPUT REGULATION FULL LOAD+5 10-200 Amps 200.0 Amps-5.2 0.4-15 Amps 10.0 Amps+12 ana

Sun-4/150SHUNTSBOARDSLOT POSITIONBG 3 IACK 1 2 3 4 5 6Out OutSun 4100 CPU (1)A AOut OutGP (4)AIn In GB AInInInInInInTAAC-1 (5) A BABABIn Out 1st MCP A

Sun-4/260SHUNTSBOARDSLOT POSITIONBG 3 IACK 1 2 3 4 5 6 7 8 9 10 11 12Out Out Sun 4200 CPU AIn In1st Memory (6)AIn In2nd Memory (6)AIn In3rd Memory (6)

In Out4th IPC (3)A B C D E F GOut Out1st Tape Ctlr (8)A B C D E FOut Out2nd Tape Ctlr (8)A B C D EOut Out1st Disk Ctlr (9)A B C D E FOut Out2nd Disk C

In Out 2nd ALM-2 A B C D E F G HIn Out 3rd ALM-2 A B C D E F GIn Out 4th ALM-2 A B C D E FOutOutOutOut1st ChannelAdapterA BABC DCEDFEGFGOutOutOutOut2n

Sun-4/280with 501-1167 SCSI Host AdapterSHUNTSBOARDSLOT POSITIONBG3 IACK 1 2 3 4 5 6 7 8 9 10 11 12Out Out Sun 4200 CPU AIn In1st Memory (6)AIn In2nd

In Out 1st HSI A B C D E F G H IIn Out 2nd HSI A B C D E F G HOut Out Ethernet A B C D E F G H IOut Out 1st FDDI A B C D E F G H IOut Out 2nd FDDI A B

InInInInInInTAAC-1 (5) EEED CDBCDABCABAOut Out 1st ALM-1 AOut Out 2nd ALM-1 AOut Out 3rd ALM-1 AOut OutSCSI (11)AIn Out 1st MCP A B C DIn Out 2nd MCP

Out Out4th Disk Ctlr (10)A B CReferencesSun Systems ardcage Slot Assignments and Backplane Configuration Procedures, 813-2004-16.1. Cardcage Slot Ass

OutInOutIn1st MAPkit A BACBCD EDFEGFHGHOutInOutIn2nd MAPkit AAB CBDCEDFEFIn Out 1st HSI D A B C E F G H I JIn Out 2nd HSI C A B D E F G H IOut Out Eth

Sun-4/280with Double-Height Backpanelwith 501-1138 or 501-1217 SCSISHUNTSBOARDSLOT POSITIONBG3 IACK 1 2 3 4 5 6 7 8 9 10 11 12Out Out Sun 4200 CPU A A

+12 motor 4-15 Amps 6.3 Amps-12 0-5 Amps 4.0 AmpsLast updated: December 2, 1996Comments and SuggestionsSun4/II: Power - Zytec 22907400 1200 Watt Power

In Out CG9 Color A BIn Out 1st HSI A B C D E F G H IIn Out 2nd HSI A B C D E F G HOut Out Ethernet A B C D E F G H IOut Out 1st FDDI A B C D E F G H I

InInInInInInTAAC-1 (5) B CBCBCAAAOut Out 1st ALM-1 AOut Out 2nd ALM-1 AOut Out 3rd ALM-1 AIn Out 1st MCP A B C DIn Out 2nd MCP A B C D E FIn Out 3rd M

Out Out4th Disk Ctlr (10)A B C DReferencesSun Systems Cardcage Slot Assignments and Backplane Configuration Procedures,813-2004-16.1. Sun-4/200 Cardc

OutOutOutOut1st ChannelAdapterA BACBCD EDEOutOutOutOut2nd ChannelAdapterAAB CBCOutInOutIn1st MAPkit A BABC DCDOutInOutIn2nd MAPkit A BABOut OutSCSI (1

Sun-4/310SHUNTSBOARDSLOTPOSITIONBG 3 IACK 1 2 3Out OutSun 4300 CPU (1)A AIn InMemory (2)A BIn OutColor (3)A BIn Out 1st MCP A BIn Out 2nd MCP AIn Out

Footnotes to Slot Assignments forSun-4/310/330/350/360/370/380/390NOTE # PART # BOARD1501-1247501-1374501-1402501-1443501-1532MG3 P4 Mono Frame Buffer

NOTE # PART # BOARD6501-1268501-1139GP2GP+NOTE # PART # BOARD7501-1381501-1447TAAC-1 Application AcceleratorTAAC-1 Application AcceleratorNOTE # PART

13501-1166501-1249Xylogics 451 Disk Controller AssemblyXylogics 7053 Disk ControllerNOTE # PART # BOARD14501-1249 Xylogics 7053 Disk ControllerNOTE #

Sun-4/330SHUNTSBOARDSLOT POSITION9U 6U 3UBG3 IACK 1 2 3 4A 5A 4B 5BOut OutSun 4300 CPU (8)A aIn Out 1st MCP B AIn Out 2nd MCP B AIn Out 1st ALM-2 B AI

Sun-4/350SHUNTSBOARDSLOT POSITIONBG3 IACK 1 2 3 4 5 6Out OutSun 4300 CPU (1)A AIn InMemory (2)AOut OutGP (6)AOut Out CG9 AInInInInInInTAAC-1 (7) A BAB

Boschert XL520-3625520 Watt Power SupplySun-4/330 / SS630300-1072Sun4/II: Power - Boschert XL520-3625 520 Watt Power Supplyhttp://lios.apana.org.au/~c

Sun-4/360SHUNTSBOARDSLOT POSITIONBG3 IACK 1 2 3 4 5 6 7 8 9 10 11 12Out OutSun 4300 CPU (1)A AIn InMemory (2)A AOut OutGP (6)AIn Out CG9 A AIn In GB A

Last updated: December 2, 1996Comments and SuggestionsSun4/I: Slot Assignment - Sun-4/360http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00

Sun-4/370SHUNTSBOARDSLOT POSITIONBG3 IACK 1 2 3 4 5 6 7 8 9 10 11 12Out OutSun 4300 CPU (1)A aIn InMemory (2)AOut Out VX A B COut Out MVX A BIn Out CG

ReferencesSPARCsystem 370 Cardcage Slot Assignments and Backplane Configuration Procedures,813-2079-11.1. Sun-3 SCSI Hosts Adapter Installation Manua

Sun-4/380SHUNTSBOARDSLOT POSITIONBG3 IACK 1 2 3 4 5 6 7 8 9 10 11 12Out OutSun 4300 CPU (1)A aIn InMemory (2)A aOut OutGP (6)AIn Out CG9 A BIn In GB A

ReferencesSPARCsystem 360 & SPARCserver 380 Cardcage Slot Assignments and BackplaneConfiguration Procedures, 813-2088-11.Last updated: December 2,

Sun-4/390SHUNTSBOARDSLOT POSITIONBG3 IACK 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16Out Out4300 CPU (1)A aIn InMemory (2)AOut Out VX A B COut Out MVX A BO

Out Out3rd IPI Ctlr (15)A B C D E F G H IOut Out4th IPI Ctlr (15)A B C D E F G HIn Out CG5 A B C D E F G H I J KIn Out CG5 w GP2 A BIn Out CG9 A BRefe

Sun-4/470SHUNTSBOARDSLOT POSITIONBG3 IACK 1 2 3 4 5 6 7 8 9 10 11 12Out Out Sun 4400 CPU A aIn In1st Memory (1)AIn In2nd Memory (1)AIn In3rd Memory (1

Out Out 1st NC400 A B C DOut Out 2nd NC400 A B COut Out 3rd NC400 A BOut Out 4th NC400 AOut Out1st SMD Ctlr (5)A B C DOut Out2nd SMD Ctlr (5)A B COut

FusesF1 = 20 Amps @ 250 VoltsF2 = 10 Amps @ 250 VoltsLast updated: December 2, 1996Comments and SuggestionsSun4/II: Power - Boschert XL520-3625 520 Wa

Footnotes to Slot Assignments forSun-4/470/490NOTE # PART # BOARD1501-1402501-1374501-1532MG4 P4 Mono Frame BufferCG6 P4 Color Frame BufferCG6 P4 Colo

Sun-4/490SHUNTSBOARDSLOT POSITIONBG3 IACK 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16Out Out Sun 4400 CPU A aIn In1st Memory (1)AIn In2nd Memory (1)AIn In3

Out Out3rd Ethernet (4)A B C D E F G H IOut Out 1st FDDI A B C D E F G H I J KOut Out 2nd FDDI A B C D E F G H I JOut Out 1st NC400 A B C D E FOut Out

BackplaneBackplane InformationSun-4/110/310Sun-4/150/350Sun-4/260/280/360/380Sun-4/370Sun-4/370/470 / SS670MPSun-4/330 / SS630MPSun-4/390/490 / SS690M

Backplane InformationThis section contains bus signal charts and backplane layout illustrations.VMEbus BackplaneCardcage slot numbers are stamped, pri

10 SYSCLK BG3IN* SYSFAIL*11 GND BG3OUT* BERR*12 DS1* BR0* SYSRESET*13 DS0* BR1* LWORD*14 WRITE* BR2* AM515 GND BR3* A2316 DTACK* AM0 A2217 GND AM1 A21

15 User Defined D17 User Defined16 User Defined D18 User Defined17 User Defined D19 User Defined18 User Defined D20 User Defined19 User Defined D21 Us

20 +5V User Defined GND21 +5V User Defined GND22 +5V User Defined GND23 +5V User Defined GND24 +5V User Defined GND25 +5V User Defined GND26 +12V User

501-1354 5-Slot BackplaneMemory board options plug into connector J3, Slots 4 and 5, on the 501-1354 backplane. The Sun P2bus connects Slots 1, 4, and

The 501-1439 Backplane terminates J2/P2, Row C, Pins 75 and 96 with a 40.2 Ohm resistor and a47pf capacitor.The 501-1598 and 501-1832 Backplanes termi

Seagate 45070625215 Watt Power SupplySeagate 97209-12G / Seagate 97229-11GOptions 706 / 707 / 709 / 710 / 716 / 717 / 719 / 720300-1074FuseAt F 100, 8

J8xx BG0-3IN to BG0-3Out and IACKIN to IACKOUT on slot 8J9xx BG0-3IN to BG0-3Out and IACKIN to IACKOUT on slot 9J10xx BG0-3IN to BG0-3Out and IACKIN t

P2 Bus A A A A A A A B C D D D16-Slot VMEbus Backplane501-1498 and 501-1597Slot 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16P2 Bus A A A A A A A B C D E E F

Sun-4/110/310501-1127PressfitPower:1.3 Amps @ +5Vdc6.5 WattsP1 Power Pinouts1-2 3-4 5 6 7 8-5 GND +12 GND -12 GNDLast updated: December 2, 1996Comment

Sun-4/150/350501-1128PressfitPower:1.3 Amps @ +5Vdc6.5 WattsSun4/I: Backplane - Sun-4/150/350http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/w

P1 Power Pinouts1-2 3-4 5 6 7 8-5 GND +12 GND -12 GNDLast updated: December 2, 1996Comments and SuggestionsSun4/I: Backplane - Sun-4/150/350http://lio

Sun-4/260/280/360/380501-1092 501-1117PressfitPower1.3 Amps @ +5Vdc6.5 WattsLast updated: December 2, 1996Comments and SuggestionsSun4/I: Backplane -

Sun-4/370501-1439PressfitTest Points DescriptionTESTPOINTDESCRIPTIONTESTPOINTDESCRIPTION1 +5 5 +122 GND 6 -5.23 +12 Motor 7 Chassis ground4 -12 8 Grou

Power2.1 Amps @ +5Vdc10.5 WattsNoteThe LED positions on the backplane and the descriptions molded into the front cover do notmatch.Last updated: Decem

Sun-4/370/470 / SS670MP501-1598PressfitTest Points DescriptionTESTPOINTDESCRIPTIONTESTPOINTDESCRIPTION1 +5 5 +122 GND 6 -5.23 +12 Motor 7 Chassis grou

Power2.1 Amps @ +5Vdc10.5 WattsSun-4/370/470 / SS670MP501-1832PressfitTest Points DescriptionTESTPOINTDESCRIPTIONTESTPOINTDESCRIPTIONSun4/I: Backplane

Notes205 Watt Power Supply 300-1041Supports one Seagate 97209-12G 3MB/Sec IPI Disk Drive.Does NOT Support the Seagate 97229-11G 6MB/Sec IPI Disk Drive

1 +5 5 +122 GND 6 -5.23 +12 Motor 7 Chassis ground4 -12 8 GroundPower:2.1 Amps @ +5Vdc10.5 WattsLast updated: December 2, 1996Comments and Suggestions

Sun-4/330 / SS630MP501-1354PressfitPower2.0 Amps @ +5Vdc10.0 WattsLast updated: December 2, 1996Comments and SuggestionsSun4/I: Backplane - Sun-4/330

Sun-4/390/490 / SS690MP501-1498PressfitTest Points DescriptionTESTPOINTDESCRIPTIONTESTPOINTDESCRIPTION1 +5 5 +122 GND 6 -5.23 +12 Motor 7 Chassis grou

Power2.1 Amps @ +5Vdc10.5 WattsSun-4/390/490 / SS690MP501-1597PressfitTest Points DescriptionTESTPOINTDESCRIPTIONTESTPOINTDESCRIPTION1 +5 5 +12Sun4/I:

2 GND 6 -5.23 +12 Motor 7 Chassis ground4 -12 8 GroundPower2.1 Amps @ +5Vdc10.5 WattsNoteThe Load Resistor is only used with the 925W power supply.Las

MiscellaneousFloating Point Unit-2 (FPU2)SunIPC6U to 9U VMEbus AdapterVMEbus to Multibus AdapterLast updated: December 2, 1996Comments and Suggestions

Floating Point Unit-2 (FPU2)Sun-4/110/150Option 154501-13844/110/150 Option PartsFront BracketRear Bracket4-40 Screw340-1743340-2163240-1196J100 Jumpe

NotesThe 501-1384 FPU2 is supported only on CPU boards 501-1512, 501-1513, 501-1514,501-1515, 501-1516, and 501-1517.1. Remove the Weitek ALU (U202)

J100 Jumper SettingsPINS SETTING DESCRIPTION1-23-45-67-8InInInOutTI chip on boardNo Tristate on all outputTI8847/TI8837Enable chaining modeNoteDiagnos

SunIPCSun-4/260/280/330/360/370/380/390Options SUNIPC / SUNIPC-87501-1125 501-1214w/o 80287 w 80287Sun4/I: Miscellaneous - SunIPChttp://lios.apana.org

Fuji PEX527-31840 Watt Power SupplyOptions 741 / 742 / 743 / 744300-1075Sun4/II: Power - Fuji PEX527-31 840 Watt Power Supplyhttp://lios.apana.org.au/

Power:5.6 Amps @ +5Vdc28.0 WattsJumper and Switch SettingsJUMPER SETTING DESCRIPTIONH05 1-2 In Enable 48MHz XTALH06 1-2 In Enable 20 MHz XTALH10 1-2 O

SW3-1SW3-2SW3-3SW3-4SW3-5SW3-6SW3-7SW3-8OnOnOffOffOffOnOffOnA23A22A21A20A19A18A17A16VME Address 3E0000; device pc3SWITCH SETTING DESCRIPTIONSW3-1SW3-2

6U to 9U VMEbus AdapterOption 160A501-1269with P2A & P2CSun4/I: Miscellaneous - 6U to 9U VMEbus Adapterhttp://lios.apana.org.au/~cdewick/sunshack/

6U to 9U VMEbus AdapterOption 160B501-1191without P2A & P2CLast updated: December 2, 1996Comments and SuggestionsSun4/I: Miscellaneous - 6U to 9U

VMEbus to Multibus AdapterOption 161501-1054Power:2.0 Amps @ +5Vdc10.0 WattsSun4/I: Miscellaneous - VMEbus to Multibus Adapterhttp://lios.apana.org.au

Note:There are no LED, switch, or cable openings in the backpanel.Last updated: December 2, 1996Comments and SuggestionsSun4/I: Miscellaneous - VMEbus

CommunicationMultibusSun-2 Ethernet ControllerVMEbus to Multibus Adapter with Sun-2 EthernetSun-3/E Ethernet AssemblySystech MTI-800/1600 ControllerSy

Sun-2 Ethernet ControllerSun-4/110/150/260/280Sun-4/310/330/350/360/370/380/390Option 450501-1004Power:6.0 Amps @ +5Vdc0.5 Amps @ +12VdcSun4/I: Commun

36.0 WattsJumper and Switch SettingsJUMPER PINS SETTING DESCRIPTIONJ101 1-21-2InOutLevel 1 EthernetLevel 2 EthernetJ400 1-2 Out M.BIG SelectJ401 1-2 O

VMEbus to Multibus Adapterwith Sun-2 EthernetSun-4/110/150/260/280/310/330/350/360Sun-4/370/380/390Option 450501-1153Sun4/I: Communication - VMEbus to

Fuse20 Amps @ 250 VoltsNotes840 Watt Power Supply 300-1075Supports four Seagate 97209-12G 3MB/Sec IPI Disk Drives.Supports four Seagate 97229-11G 6MB/

Power:5.8 Amps @ +5Vdc29.0 WattsVME TO MULTIBUS ADAPTER BOARD SWITCH SETTINGSSWITCH 1 2 3 4 5 6 7 8 DESCRIPTIONU1 N/C ON ON ON ON ON ON ON I-O Address

Sun-3/E Ethernet AssemblySun-4/390/470/490Option 452501-1584Power:4.1 Amps @ +5Vdc20.5 WattsSun4/I: Communication - Sun-3/E Ethernet Assemblyhttp://li

NotesBoard revision 501-8027-06 or 501-1584-01 is required for use in any SPARC CPU basedsystem.1. When used with the Sun-4400 CPU, 501-1381, the boa

ReferenceSun SunNet Ethernet/VME Controller Configuration Procedures, 813-2082-10.Last updated: December 2, 1996Comments and SuggestionsSun4/I: Commun

Systech MTI-800/1600 ControllerAsychronous Line Multiplexer 1 (ALM-1)Sun-4/260/280Options 480 / 481370-1047Sun4/I: Communication - Systech MTI-800/160

Switch Settingsmt0 DefaultsDIP SWITCH SETTING DESCRIPTIONSW2 12345678OffOffOffOffOffOnOnOffAddress select A15Address select A14Address select A13Addre

Systech MTI-850/1650 ControllerAsychronous Line Multiplexer 1 (ALM-1)Sun-4/260/280Options 480 / 481370-1099Sun4/I: Communication - Systech MTI-850/165

Switch Settingsmt0 DefaultsDIP SWITCH SETTING DESCRIPTIONSW2 12345678OffOffOffOffOffOnOnOffAddress select A15Address select A14Address select A13Addre

W1W2W3W4W5W6W7OutOutInOutOutInIn+12Vdc routing to data cable disabled-12Vdc routing to data cable disabledNormal transfer acknowledge delayExtra 100 n

VMEbus to Multibus Adapterwith Systech MTI-1600Sun-4/260/280Option 481501-1157-01Sun4/I: Communication - VMEbus to Multibus Adapterhttp://lios.apana.o

Zytec 22914300268 Watt Power SupplyOptions 726 / 727300-1085Sun4/II: Power - Zytec 22914300 268 Watt Power Supplyhttp://lios.apana.org.au/~cdewick/sun

Power:7.1 Amps @ +5Vdc0.6 Amps @ +12Vdc0.4 Amps @ -12Vdc47.5 WattsLast updated: December 2, 1996Comments and SuggestionsSun4/I: Communication - VMEbus

VMEbus to Multibus Adapterwith Systech MTI-1650Sun-4/260/360Option 481501-1157-02Sun4/I: Communication - VMEbus to Multibus Adapterhttp://lios.apana.o

Power:7.1 Amps @ +5Vdc0.6 Amps @ +12Vdc0.4 Amps @ -12Vdc47.5 WattsVME TO MULTIBUS ADAPTER BOARD SWITCH SETTINGSSWITCH 1 2 3 4 5 6 7 8 DESCRIPTIONU1* N

Last updated: December 2, 1996Comments and SuggestionsSun4/I: Communication - VMEbus to Multibus Adapterhttp://lios.apana.org.au/~cdewick/sunshack/dat

VMEbus to Multibus Adapterwith Systech MTI-1650ASun-4/260/280/360/380Option 481501-1165Power:7.1 Amps @ +5Vdc0.6 Amps @ +12VdcSun4/I: Communication -

0.4 Amps @ -12Vdc47.5 WattsVME TO MULTIBUS ADAPTER BOARD SWITCH SETTINGSSWITCH 1 2 3 4 5 6 7 8 DESCRIPTIONU1* N/C ON ON OFF ON ON OFF OFF I-O AddressU

MAPKITSun-4/260/280/390501-1202NotesInstall the Token Bus Controller in the left slot of the adapter.1. Install the Token Bus Modem in the right slot

Jumper SettingsJUMPER PINS VALUE DESCRIPTIONJ1 1-24-65-79-113 Bus request levelJ2 3-54-63 Bus request levelJ3 3-4 16 sec Watchdog timerJ4 1-23-45-67-8

Asynchronous Line Multiplexor-2Sun-4/110/150/260/280Sun-4/310/330/350/360/370/380/390/470/490SS600MP501-1203Power:7.0 Amps @ +5Vdc0.2 Amps @ -5Vdc36.0

Jumper and Switch SettingsJUMPER PINS SETTING DESCRIPTIONJ0201 1-2 In Test jumper for oscillatorJ0202 32 Bit In VME address bus sizeJ0202 24 Bit OutJ1

Fuse10 Amps @ 250 VoltsLast updated: December 2, 1996Comments and SuggestionsSun4/II: Power - Zytec 22914300 268 Watt Power Supplyhttp://lios.apana.or

ReferenceAsynchronous Line Multiplexor-2 Configuration Procedures, 813-2042.Last updated: December 2, 1996Comments and SuggestionsSun4/I: Communicatio

Multiprotocol CommunicationProcessorSun-4/110/150/260/280Sun-4/310/330/350/360/370/380/390/470/490SS600MP501-1221Power:7.0 Amps @ +5Vdc0.2 Amps @ -5Vd

36.0 WattsJumper and Switch SettingsJUMPER PINS SETTING DESCRIPTIONJ0201 1-2 In Test jumper for oscillatorJ0202 32 Bit In VME address bus sizeJ0202 24

SunLink Channel AdapterSun-4/260/280/350/360/370/380/390/470/490SS670MP / SS690MP370-1128 501-1460Board Set Board SetBackpanel and ConnectorsPower:8.6

ReferenceSunLink Channel Adapter Configuration Procedures, 813-2040-10.CIO BoardSun4/I: Communication - SunLink Channel Adapterhttp://lios.apana.org.a

IBD BoardJumper SettingsJUMPER PINS SETTING DESCRIPTIONB1C 7-8OthersInOutVME bus request level BR gives level 3B1A 2-36-710-1113-1415-16InInInInInBus

B8P 7-83-45-67-8InOutOutOutLocal processor external bus pageselection BS gives page 0B8U 1-23-45-67-8InOutOutOutInterrupt acknowledge page selectionIA

Jumper SettingsJUMPER PINS SETTING DESCRIPTIONJM01 All Out VME BERR timeout 67.1 secondsJM02 All Out VME LBERR timeout 107.4 secondsJM03 2-43-5InInSYS

High-speed Serial Interface (HSI)Sun-4/110/150/260/280/330/350/390/470/490501-1338Power:5.3 Amps @ +5Vdc0.3 Amps @ -5Vdc28.1 WattsNotesSCSI-3 Host Ada

>=501-1164-09, or any revision of 501-1208.The minimum operating system is SunOS 4.0.4. The High-speed Serial Interface is not supported in Solari

Brown 300-1020575 Watt Power SupplySun-4/150/350300-1020Sun4/II: Power - Brown 300-1020http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd0000

Fuji PEX526-30925 Watt Power SupplySun-4/370/470300-1089DC OUTPUT REGULATION FULL LOAD+5 150 Amps 145.0 Amps-5.2 15 Amps 10.0 Amps+12 analog 15 Amps 2

Last updated: December 2, 1996Comments and SuggestionsSun4/I: Communication - High-speed Serial Interface (HSI)http://lios.apana.org.au/~cdewick/sunsh

FDDI/DXSun-4/110/150/260/280/330/350/390/470/490SS630MP / SS670MP / SS690MPOption 461501-1276Power:11.2 Amps @ +5Vdc0.1 Amps @ -5VdcSun4/I: Communicat

1.9 Amps @ +12Vdc0.7 Amps @ -12Vdc87.7 WattsSwitch SettingsNotesUse 2A subminiature Fuse 150-1174.1. The Sun 3004 CPU must be 501-1163-09, 501-1164-0

Comments and SuggestionsSun4/I: Communication - FDDI/DXhttp://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0051f.htm (3 von 3) [25.04.

Sun Network CoProcessorSun-4/470/490SS630MP / SS670MP / SS690MPOption 176370-1396 / 370-1421Sun4/I: Communication - Sun Network CoProcessorhttp://lios

Power:8.0 Amps @ +5Vdc0.5 Amps46.0 WattsInterphase Release 1.4 Switch SettingsSun4/I: Communication - Sun Network CoProcessorhttp://lios.apana.org.au/

Address Switches and Address Bit AssignmentsDIP SWITCH 1 2 3 4 5 6 7 8SW1 A15 A14 A13 A12 A11 A10 A09 AMSW2 A23 A22 A21 A20 A19 A18 A17 A16SW3 A31 A30

NotesSNC 1.2 requires Sun 4400 CPU 501-1381-09 or 501-1899-01.1. SNC 1.2 requires IPI Firmware 525-1023-05, 525-1024-10, and 525-1025-10. This firmwa

ReferencesNC300/NC400 Network CoProcessor Release 1.4 Installation Manual.1. Sun Network CoProcessor 1.0 Installation Manual, 800-6881-10.2. Sun Net

Power:8.0 Amps @ +5Vdc0.5 Amps46.0 WattsSNC 1.2 Jumper SettingsSun4/I: Communication - Sun Network CoProcessorhttp://lios.apana.org.au/~cdewick/sunsha

Last updated: December 2, 1996Comments and SuggestionsSun4/II: Power - Fuji PEX526-30 925 Watt Power Supplyhttp://lios.apana.org.au/~cdewick/sunshack/

Address Jumpers and Address Bit AssignmentsJUMPER JP1 JP2 JP3 JP4 JP5 JP6 JP7 JP8ADDRESS BIT A31 A30 A29 A28 A27 A26 A25 A24JUMPER JP9 JP10 JP11 JP12

ADDRESS BIT A15 A14 A13 A12 A11NotesSNC 1.2 requires Sun 4400 CPU 501-1381-09 or 501-1899-01.1. SNC 1.2 requires IPI Firmware 525-1023-05, 525-1024-1

Removable Media1/4" Tape ControllerEmulex MT02CD-ROM DrivesSony CDU-8012 (SunCD)1/4" Tape Drives60MB150MB8 mm Tape Drives2.3GB1/2" Tape

Emulex MT02Sun-4/260/280/360/380Options 511 / 514 / 516370-1061 / 370-1235KEYLED 1(Green)LED 2(Red)STATE0 = Off 0 0 Power up reset clear1 = On 1 1 Pow

Switch and Jumper SettingsDIP SWITCH SWITCH SETTING DESCRIPTIONSW1 1 Off Bit 02 Off Bit 13 On Bit 2-SCSI device address 044 Off Not used56OnOffArchive

Comments and SuggestionsSun4/I: Removable Media - Emulex MT02http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005b1.htm (3 von 3) [

Sony CDU-8012 (SunCD)Sun-4/330/370/390/470/490SS600MP / SS1000 / SC2000Options 558 / 559370-1312 370-1347Lt Grey Bezel Black BezelFront ViewRear ViewI

Power0.5 Amps @ +5Vdc0.5 Amps @ +12Vdc8.5 WattsNotesThe Sun CD-ROM requires 1.0 SunCD for SunOS 4.0.3c.1. Use 370-1347-03 when mounted on-end in the

60MB 1/4" Tape DriveSun-4/260/280/360/380Options 515 / 514 / 516370-1076 370-1103Wangtech5099EN24Wangtech5099EN24Archive5945CRear View of Wangtec

Power1.0 Amps @ +5Vdc1.9 Amps @ +12Vdc27.8 WattsNoteThis tape drive is used with the Emulex MT02.60MB 1/4" Tape Drivewith Emulex MT02 Tape Contro

Fuji PEX614-30820 Watt Power SupplyOptions 750 / 754 / 756300-1091Sun4/II: Power - Fuji PEX614-30 820 Watt Power Supplyhttp://lios.apana.org.au/~cdewi

SW1 1 & 23OffOnSCSI target 4SCSI target 41 & 32OnOffSCSI target 5SCSI target 54567OffOnOffOffNot usedArchive tape driveArchive tape driveDrive

150MB 1/4" Tape DriveSun-4/330/370/390/470/490SS630MP / SS670MP / SS690MP / SC2000Options 539 / 565 / 660370-1205 370-1206 370-1218 370-1246Archi

Power0.7 Amps @ +5Vdc1.5 Amps @ +12Vdc21.5 WattsJumper SettingsJUMPER SETTING DESCRIPTION USAGERXD/TXD Out Serial Port Not usedDIAGParityOutOut*Normal

2.3GB 8 mm Tape DriveSun-4/370/390/470/490SS670MP / SS690MPOptions 566 / 802 / 804370-1297 370-1405Exabyte EXB-8200Black BezelExabyte EXB-8200Lt Grey

Power4.0 Amps @ +5Vdc1.2 Amps @ +12Vdc34.4 WattsMX CardDip Switch U32SWITCH SETTING DESCRIPTION1 On Bypass memory test2 On Enable parity checking3 On

ECO WO_01575 enabled Parity checking on the MX card. Parity checking is disabled ondrives shipped prior to December 1991.3. ReferencesSun 2.3-Gbyte 8

HP 88780 Front Load Tape DriveOptions 680 / 682 / 683 / 684Read/Write/Format Board370-1276Drive Controller Board370-1277Single Ended I/O Board811-1241

Data Buffer Board370-1279NVRAM Reset ProcedureLoad a scratch tape.1. Run TEST 150 to write a GCR ID to the scratch tape.2. Run TEST 128 to store the

Run TEST 129 to load NVRAM with the contents stored on tape.12. Rewind to BOT.13. Run TEST 99 to calibrate the read channel gain values.14. Battery

SCSI DiskSingle Ended SCSI Disk DrivesCDC 94171-327/344 (327MB)Micropolis 1588-15 (669MB)Maxtor XT-8760S (669MB)Seagate ST41600N (1.3GB)Last updated:

FuseLittelfuse BLN 20Last updated: December 2, 1996Comments and SuggestionsSun4/II: Power - Fuji PEX614-30 820 Watt Power Supplyhttp://lios.apana.org.

CDC 94171-327/344 (327MB)5 1/4" 3600 RPM Embedded SCSISun-4/330/370/470Options RREXP-P7 / RR129 / RR134Options 526 / 527 / 530 / 539555-1005 370-

Terminator Power Source Select Jumper J5Power1.5 Amps @ +5Vdc1.4 Amps @ +12Vdc24.3 WattsJumper Settings555-1005 and 370-1153 OnlyJ3PIN SETTING DESCRIP

Address Jumper SettingsJ4PIN SETTING DESCRIPTION TARGET1, 2, 4 Out Drive select Target 01 In Drive select Target 12 In Drive select Target 21, 2 In Dr

Last updated: December 2, 1996Comments and SuggestionsSun4/I: SCSI Disk - CDC 94171-327/344 (327MB)http://lios.apana.org.au/~cdewick/sunshack/data/feh

Micropolis 1588-15 (669MB)5 1/4" 3600 RPM Single Ended SCSISun-4/330/370/470Options 561 / 563 / 565 / 566370-1319 370-1326 555-1151FS0013-03-5Bla

Option Jumper SettingsJUMPER SETTING DESCRIPTIONW5 Out Spindle starts at power onW4 Out Enable parity detectionW1W2W11InOutOutDrive provides internal

Address Jumper SettingsJ2 Multi-function ConnectorPIN SETTING DESCRIPTION0,1, 2 Out Target 00 In Target 11 In Target 20,1 In Target 3References5-1/4&q

Maxtor XT-8760S (669MB)5 1/4" 3600 RPM Single Ended SCSISun-4/330/370/470Options 561 / 563 / 565 / 566370-1319 370-1326 555-11511098618-BBlack Be

Address DescriptionThe address is set on the J2 Adapter installed in the J2 Auxiliary connector, the Address Select switchon the External Storage Modu

J2 Auxiliary Connector with Adapter 811-1682-01JUMPER SETTING DESCRIPTION1,2,4 Out Target 01 In Target 12 In Target 21,2 In Target 3JP35, JP36, and JP

Fuji PEX614-31800 Watt Power SupplyOptions 750 / 754 / 756 / 762 / 763 / 764300-1106Sun4/II: Power - Fuji PEX614-31 800 Watt Power Supplyhttp://lios.a

Seagate ST41600N (1.3GB)976002-012 Elite-1 Family5 1/4" 5400 RPM Single Ended SCSISun-4/470 / SS630MP / SS670MPOption 571370-13773 1/4" Heig

In the Desktop Storage Module, orient Pin-1of the Address Select Switch Cable with ID2on J5. Remove all jumpers from J4A.Power2.4 Amps @ +5Vdc2.1 Amps

SCO Out Spinup according to SD0 settingSCP Out Parity enabledSWP In Sweep cycle enabledJ01JUMPER SETTING DESCRIPTION1-2 The drive supplies TERMPWR to

SCSIESDIEmulex MD21VMEbusSun-2 SCSI Host AdapterBlank SCSI Adapter AssemblySun-3 SCSI Host AdapterSun-3/E SCSI/EthernetLast updated: December 2, 1996C

Emulex MD21Sun-4/260Options 504 / 505 / 507 / 509 / 510 / 514 / 516370-0552 / 370-1236Power1.6 Amps @ +5Vdc8.0 WattsSun4/I: SCSI - Emulex MD21http://l

Switch and Jumper SettingsDIPSWITCHSETTING DESCRIPTION123Off*OffOffSCSI BUS ADDRESS/TARGETBit 0-74 Off Not used5 Off 512 byte/sector6 Off Power on spi

Sun-2 SCSI Host AdapterSun-4/260/280501-1045Power2.8 Amps @ +5Vdc14.0 WattsSun4/I: SCSI - Sun-2 SCSI Host Adapterhttp://lios.apana.org.au/~cdewick/sun

Switch and Jumper SettingsJUMPER PINS SETTING DESCRIPTIONJ500 1-23-45-67-8OutOutOutInBus Grant 0 InBus Grant 1 InBus Grant 2 InBus Grant 3 InJ501 1-23

Power2.7 Amps @ +5Vdc13.5 WattsSun-2 SCSI Host Adapter AssemblySun-4/260501-1149with P2A and P2CSun4/I: SCSI - Sun-2 SCSI Host Adapterhttp://lios.apan

Power2.7 Amps @ +5Vdc13.5 WattsSun-2 SCSI Host Adapter AssemblySun-4/280501-1167with P2A and P2CSun4/I: SCSI - Sun-2 SCSI Host Adapterhttp://lios.apan

FuseLittelfuse BLN 20Last updated: December 2, 1996Comments and SuggestionsSun4/II: Power - Fuji PEX614-31 800 Watt Power Supplyhttp://lios.apana.org.

Power2.7 Amps @ +5Vdc13.5 WattsLast updated: December 2, 1996Comments and SuggestionsSun4/I: SCSI - Sun-2 SCSI Host Adapterhttp://lios.apana.org.au/~c

Blank SCSI Adapter AssemblySun-4/360501-1666with P2A and P2CLast updated: December 2, 1996Comments and SuggestionsSun4/I: SCSI - Blank SCSI Adapter As

Sun-3 SCSI Host AdapterSun-4/260/280/330/370/390/490501-1236Power4.8 Amps @ +5Vdc24.0 WattsSun4/I: SCSI - Sun-3 SCSI Host Adapterhttp://lios.apana.org

Switch SettingsDIPSWITCHSWITCH SETTING DESCRIPTIONSW1*U40912345678OnOnOffOnOnOnOnOnAddress A23Address A22Address A21Address A20Address A19Address A18A

Sun-3 SCSI Host Adapter AssemblySun-4/260501-1170with P2A and P2CPower4.8 Amps @ +5Vdc24.0 WattsSun4/I: SCSI - Sun-3 SCSI Host Adapterhttp://lios.apan

Sun-3 SCSI Host Adapter AssemblySun-4/280/330/370/390/470/490501-1217without P2A and P2CPower4.8 Amps @ +5Vdc24.0 WattsLast updated: December 2, 1996S

Comments and SuggestionsSun4/I: SCSI - Sun-3 SCSI Host Adapterhttp://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005d0.htm (5 von 5)

Sun-3/E SCSI/Ethernet501-8027 501-15849U AssemblyEthernet OnlyPower4.1 Amps @ +5Vdc20.5 WattsNotesBoard revision 501-8027-06 or 501-1584-01 is require

When used with the Sun-4400 CPU, 501-1381, the board revision must be >=501-8027-07 orthe assembly must be >=501-1584-02.3. SCSI TERMPWR is pro

Note: The SCSI base address under SunOS 3.5 diag is 31000.Last updated: December 2, 1996Comments and SuggestionsSun4/I: SCSI - Sun-3/E SCSI/Ethernetht

Fujitsu M2444AC Power Supply A-1Options 78 / 675811-1027Sun4/II: Power - Fujitsu M2444AC Power Supplyhttp://lios.apana.org.au/~cdewick/sunshack/data/f

IPIIPI Disk ControllerISP-80 / IPI-2IPI Disk DrivesSeagate 97229-11G (911MB)Seagate 97209-12G (1.2GB)Seagate 975002-005 (1.3GB)Last updated: December

ISP-80 / IPI-2Sun-4/390/470/490SS670MP / SS690MPOptions 408 / 418501-1539 / 501-1855Power:11.8 Amps @ +5Vdc59.0 WattsSun4/I: IPI - ISP-80 / IPI-2http:

Base Address Select SwitchesDIP SWITCH 1 2 3 4 5 6 7 8SW1603 AM0 AM1 A10 A11 A12 A13 A14 A15SW1602 A16 A17 A18 A19 A20 A21 A22 A23SW1601 A24 A25 A26 A

Jumper JM2PINS SETTING DESCRIPTION1-2 In Enable UART clockISP-80 / IPI-2A minimum ISP-80 firmware level is required to support these products.PRODUCT

Comments and SuggestionsSun4/I: IPI - ISP-80 / IPI-2http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00579.htm (4 von 4) [25.04.200

Seagate 97229-11G (911MB)Equipment Number PA8Y28" 3600 RPM IPI-2 6MB/SecOptions 716 / 717 / 719 / 720 / 741L / 742L / 743L /744L / 745LOperator P

NoteEach drive power-on sequence is delayed for a time equal to five seconds times its address. Forexample, if the address is 3, the drive starts afte

I/O Board Rear ViewPower Connector15 14 13 12 11 10 9 8 7 6 5 4 3 2 1+24RTN+24 +24 +24 +24RTN+24RTNN/C PWROK-12 -5 -5 GND GND +5 +5Dip Switch 1 Settin

5678OpenClosedOpenClosed1D 31D 21D 11D 0ID Microcode. Do Not Change"""9 Open Slave/Master spindle sync-slaveNotesThe 911MB Disk require

Seagate 97209-12G (1.2GB)Equipment Number PA8R28" 3600 RPM IPI-2 3MB/SecOptions 706 / 707 / 709 / 710 / 741A / 742A / 743A /744A / 745AOperator P

Fujitsu M2444AC Power Supply A-2Options 78 / 675811-1027Sun4/II: Power - Fujitsu M2444AC Power Supplyhttp://lios.apana.org.au/~cdewick/sunshack/data/f

NoteEach drive power on sequence is delayed for a time equal to five seconds times its address. Forexample, if the address is 3, the drive starts afte

I/O Board Rear ViewPower Connector15 14 13 12 11 10 9 8 7 6 5 4 3 2 1+24RTN+24 +24 +24 +24RTN+24RTNN/C PWROK-12 -5 -5 GND GND +5 +5Dip Switch 1 Settin

1234OpenClosedOpenClosedDrive starts when DC Power is appliedDisable Port BEnable Port ADisable internal diagnostics5678OpenClosedOpenClosed1D 31D 21D

Seagate 975002-005 (1.3GB)Equipment Number PA4F2/ST41201K5 1/4" / 5400 RPM / IPI-2 / 3.25-4.5MB/SecSun-4/490 / SS690MPOptions 726 / 727 / 728370-

Power:2.7 Amps @ +5Vdc2.0 Amps @ +12Vdc37.5 WattsServo Board Switch SettingsSun4/I: IPI - Seagate 975002-005 (1.3GB)http://lios.apana.org.au/~cdewick/

I/O Transceiver Board Switch SettingsNotesThe minimum operating system is SunOS 4.1.1.1. SunOS 4.1.1 and SunOS 4.1.1 Rev B require the 1.3GB Disk Dri

GraphicsVMEbusGP Graphics ProcessorGP+ Graphics Processor PlusGP Graphics BufferCG3 Sun 3160 Color Frame BufferCG5 Color Frame BufferGP2 Graphics Proc

GP Graphics ProcessorSun-4/150/260/280/330/350/360/370/380501-1055UNIX ID: /dev/gpone0a-dPowerGP16.4 Amps @ +5Vdc82.0 WattsSun4/I: Graphics - GP Graph

Jumper and Switch SettingsJUMPER SETTING DESCRIPTIONJ1 Out GP board ID bit 3J2 In GP board ID bit 4J3 In GP board ID bit 2J4 Out GP board ID bit 5J5 O

Last updated: December 2, 1996Comments and SuggestionsSun4/I: Graphics - GP Graphics Processorhttp://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/

Last updated: December 2, 1996Comments and SuggestionsSun4/II: Power - Fujitsu M2444AC Power Supplyhttp://lios.apana.org.au/~cdewick/sunshack/data/feh

GP+ Graphics Processor PlusSun-4/150/260/280/330/350/360/370/380501-1139UNIX ID: /dev/gpone0a-dPowerGP+14.6 Amps @ +5Vdc73.0 WattsSun4/I: Graphics - G

Jumper and Switch SettingsJUMPER SETTING DESCRIPTIONJ1 Out GP board ID bit 3J2 In GP board ID bit 4J3 In GP board ID bit 2J4 Out GP board ID bit 5J5 O

Last updated: December 2, 1996Comments and SuggestionsSun4/I: Graphics - GP+ Graphics Processor Plushttp://lios.apana.org.au/~cdewick/sunshack/data/fe

GP Graphics BufferSun-4/150/260/280/360/370/380501-1058Power2.1 Amps @ +5Vdc10.5 WattsSun4/I: Graphics - GP Graphics Bufferhttp://lios.apana.org.au/~c

Jumper and Switch SettingsJUMPER SETTING DESCRIPTIONJ1 Out Ground test pointJ2 Out Ground test pointJ3 Out Manual reset test pointJ4 (2-3) In Graphics

CG3 Sun 3160 Color Frame BufferSun-4/110/150/260/280/310/330/350/360/370/380501-1116 501-1089 501-1319Single Buffered Double Buffered* 1Kx1K*Double bu

2.9 Amps @ -5Vdc 3.1 Amps @ -5Vdc0.1 Amps @ +12Vdc 0.1 A mps @ +12Vdc0.2 Amps @ -12Vdc 0.2 Amps @ -12Vcd59.0 Watts 61.2 WattsJumper and Switch Setting

ReferencesInstallation Notes for the GP2 and CG5 Boards, 800-2330.1. Sun-3 Color Board Configuration Procedures, 813-2030.2. Last updated: December

CG5 Color Frame BufferSun-4/110/150/260/280Sun-4/310/330/350/360/370/380/380Sun-4/470/490501-1267UNIX ID: /dev/cgtwo0Power8.8 Amps @ +5Vdc3.2 Amps @ -

0.2 Amps @ +12Vdc0.1 Amps @ -12Vdc64.2 WattsSwitch SettingsSWITCH SETTING DESCRIPTIONSW300-1SW300-2SW300-3SW300-4SW300-5SW300-6SW300-7SW300-8OffOffOff

HP 88780 Power/Motor Drive PowerSupplyOptions 680 / 682 / 683 / 684811-1242NoteUse 6 Amp fuse 140-1021-01.Last updated: December 2, 1996Comments and S

SW3300-1SW3300-2SW3300-3SW3300-4SW3300-5SW3300-5SW3300-6SW3300-7SW3300-8OnOffOffOffOffOnOffOffOffSelects board 0Selects board 1Selects board 2Selects

GP2 Graphics ProcessorSun-3/150/160/180/260/280/460/470/480Sun-4/150/260/280/330/350/360/370/380Sun-4/390/470/490501-1268UNIX ID: /dev/gpone0a-dSun4/I

Power12.1 Amps @ +5Vdc60.5 WattsSwitch SettingsDIP SWITCH SETTING DESCRIPTIONU1601-1U1601-2U1601-3U1601-4U1601-5U1601-6U1601-7U1601-8OffOnOnOffOnOnOn/

CG9 24-bit Color Frame BufferSun-3/260/460/470/480Sun-4/150/260/280/330/350/360/370/380/390/470/490501-1434UNIX ID: /dev/cgnine0Power14.6 Amps @ +5Vdc

NotesThe GP2 must be 501-1268-07 when used with CG9.1. The CG9 is not supported with the GP or GP+.2. CG9 must be >=501-1434-04 for use with the

SW3 S0700DIP SETTING DESCRIPTION12345OffOffOffOffOnP2 Bus enableSelects board 3Selects board 2Selects board 1Selects board 0678OnOffOnN/CN/CN/CReferen

TAAC-1 Application AcceleratorSun-4/260/280/360/370/380/390/470/490501-1383 / 501-1447POP BoardUNIX ID: dev/taac0Sun4/I: Graphics - TAAC-1 Application

Power23.9 Amps @ +5Vdc0.4 Amps @ -5Vdc0.2 Amps @ +12Vdc123.9 WattsDFB BoardDFB Board Jumper and Switch SettingsJumper JB231ROW SHUNTS DESCRIPTION1 B -

2-7* Not Used Base addressing8910111212138C - 9BEmptyB-CB-CB-C12D - 13DB-CBGINVMBG IN/OUT 0VMBG IN/OUT 1VMBG IN/OUT 2Enable 50MHz CLKVMBG IN/OUT 3* Ju

VX and MVX Visualization AcceleratorsBoard Set501-1537 / 501-1538NoteTighten Frontplane Connector screws 1, 2, 3, and 4 in sequence, turning each scre

Fuse10 Amps @ 250 VoltsLast updated: December 2, 1996Comments and SuggestionsSun4/II: Power - Brown 300-1020http://lios.apana.org.au/~cdewick/sunshack

AC PowerAC Power SequencerRemote and Local Bus ConnectorsPower Requirements300-1011 -- Pulizzi Engineering -- 115V370-1027 -- Pulizzi Engineering -- 2

NotesThe minimum operating system is SunOS 4.1.1.1. The final unbundled software release was SunVision 1.2.2. The minimum operating system for SunVi

Power:14.0 Amps @ +5Vdc1.45 Amps @ -5Vdc88.0 WattsSwitch SettingsInterrupt Request Switch S0101SWITCH SETTING REQUEST BIT1234UpDownDownUp210VMRQSun4/I

VME Bus Address Switch S0102SWITCH SETTING ADDRESS BIT12345678OnOnOffOffOnOnOnOn/OffA31A30A29A28A27A26A25Not usedVX Bus Address Switch S0301SWITCH SET

Power:14.0 Amps @ +5Vdc70.0 WattsSwitch and Jumper SettingsClock Jumper J0101PIN SETTING DESCRIPTION1-2 In Enable 80MHz clockSun4/I: Graphics - VX and

Bus Request Jumper J0901PIN SETTING DESCRIPTION3-45-67-8InOutInVME BUS REQUEST 1VME BUS REQUEST 2VME BUS REQUEST 3Bus Grant Jumper J0902PIN SETTING DE

Sun-3/E Monochrome Frame Buffer501-8020UNIX ID: /dev/bwtwo0Power3.0 Amps @ +5Vdc15.0 WattsLast updated: December 2, 1996Comments and SuggestionsSun4/I

Sun-3/E Color Frame Buffer501-8029Jumper J100 SettingsJUMPER PINS SETTING DESCRIPTIONJ100J100J1001-23-45-6InOutInBase address=FF400000J100 7-8 OutUNIX

NotesThe Sun-3/E Color Frame Buffer requires a 3/E CPU, >=501-8028-07.1. This board requires SunOS 3.5 or greater.2. Last updated: December 2, 19

MG3 ECL Monochrome Frame BufferSun-4/110/150/310/330/350/370/390/470/490501-1247 501-1637w 3/80 BackpanelJumper J5401 SettingsJUMPER PINS SETTING DESC

NotesSet EEPROM location 0x1f to 20.1. The auto-select feature requires cable 530-1336 or 530-1359.2. Hi Resolution Monitor 540-1427 must be Motorol

AC Power SequencerRemote and Local Bus Connectors300-1011 / 300-1263 / 300-1264370-1126 / 370-1127 / 370-1155 / 370-1156Remote I/O Connectors J6, J7,

MG4 Analog/ECL Frame BufferSun-4/310/330/350/370/380/390/470/490501-1402w 3/80 BackpaneUNIX ID: /dev/bwtwo0Power:3.3 Amps @ +5Vdc16.5 WattsLast update

CG4 Color Frame BufferSun-4/110/150/310/330/350/370/380/390/470/490501-1248 501-1443BNC DB13W3w 3/80 BackpanelJ700 SettingPINS SETTING DESCRIPTION1-2

Power: 501-14433.8 Amps @ +5Vdc19.0 WattsLast updated: December 2, 1996Comments and SuggestionsSun4/I: Graphics - CG4 Color Frame Bufferhttp://lios.ap

CG6 Color Frame BufferSun-4/110/150/310/330/350/370/380/390/470/490501-1374 501-1505 501-1532w 3/80 BackpaneJUMPER PINS SETTING DESCRIPTIONJ100J500J50

NotesSun-3/60, Sun-4100, and Sun-4300 CPU boards require EPROM Revision 3.0 or greater.1. Set CPU EEPROM location 0x1F to 0x20.2. The minimum operat

CG8 24-bit Color Frame BufferSun-4/110/150501-1371 501-1518 501-1577BNC DB13W3 w 3/80 Rear PanelDB13W3UNIX ID: /dev/cgeight0Power501-1371 and 501-1518

NotesThere are no jumpers or switches on this board.1. Set CPU EEPROM location 0x1F to 0x20.2. Requires SunOS 4.0 CG8 or 4.0.3 or greater.3. SunOS

MG1 ECL Monochrome Frame BufferSun-4/15/30/40/50/60/65/75Sun-4/E / SS10 / SS20 / SS600 / SC2000501-1419 501-8043w 4/E BackpanelJumper JMP4PINS SETTING

Power:1.3 Amps @ +5Vdc6.5 WattsLast updated: December 2, 1996Comments and SuggestionsSun4/I: Graphics - MG1 ECL Monochrome Frame Bufferhttp://lios.apa

MG2 Analog Frame BufferSun-4/15/30/40/50/60/65/75SS4 / SS5 / SS10 / SS20 / SS600501-1455 501-8062w 4/E BackpaneJumper JMP5PINS SETTING DESCRIPTION1-21

LOCAL The AC output of the Switched 1 and Switched 2 outlets isenabled when the Circuit Breaker is ON.Last updated: December 2, 1996Comments and Sugge

Power:0.4 Amps @ +5Vdc2.0 WattsNoteThe MG2 Frame Buffer produces a 1-bit Analog output.MG2 Analog Frame BufferSun-4/15/30/40/50/60/65/75SS4 / SS5 / SS

UNIX ID: /dev/bwtwo0Power:0.3 Amps @ +5Vdc1.6 WattsNoteThe MG2 Frame Buffer produces a 1-bit Analog output.Last updated: December 2, 1996Comments and

CG3 Color Frame BufferSun-4/15/30/40/50/60/65/75SS4 / SS5 / SS10 / SS20501-1415 501-8044FAB 270-1415 w 4/E BackpanelUNIX ID: /dev/cgthree0Power:0.7 Am

Comments and SuggestionsSun4/I: Graphics - CG3 Color Frame Bufferhttp://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0055f.htm (2 von

MemorySIMMsSun-4/260/280Sun-4/330Sun 4300Sun 4400Sun-4/E (4MB)Sun-4/E (16MB)Sun-4/E (Combo)Last updated: December 2, 1996Comments and SuggestionsSun4/

SIMMsAn x indicates the SIMM(s) was installed at the factory or included in a memory expansion option.An s indicates the SIMM(s) was tested and is sup

Sun-4mSIZE SPEED SIMM P/N 4/10 4/15 4/30 SS4 SS5 SS10 SS20 SS600 Java1MB 100ns 501-1466 s*1MB 100ns 501-1565 s*1MB 60ns 501-2289 x2MB 60ns 501-2433 x4

Sun-4/260/280501-1102 501-1254 501-1451 501-15768MB ECC 32MB ECC 32MB ECC 16MB ECCPower8MB12.3 Amps @ +5Vdc61.5 Watts32MB14.0 Amps @ +5Vdc70.0 WattsSu

Memory Board LEDsJumper SettingsNotesThe Sun 4200 CPU requires EPROM 3.0 or greater when more than two 16MB ECC memoryboards are installed.1. 501-109

ReferencesSun 501-1102 Memory Board Configuration Procedures, 813-2018.1. Installation Notes for the 32MB Memory Board, 800-2123.2. 16 MB ECC Memory

AC Sequencer Power Requirements300-1011 / 300-1027 / 300-1263300-1264 / 370-1126 / 370-1155 / 370-1156Operating RangeNominal Voltage: 208, 220, 230, o

Sun-4/330501-1723501-1436501-1711501-1317501-1755501-17048MB Parityw 1MB SIMMS16MB Parityw 1MB SIMMS32MB Parityw 4MB SIMMSJumper SettingsJUMPER PINS S

Power:1.1 Amps @ +5Vdc5.5 WattsNoteThe Sun-4/330 memory uses 1MB SIMM 501-1408, 501-1466, 501-1544, 501-1565, or501-1697, or 4MB SIMM 501-1682.Referen

Sun 4300Sun-4/310/350/360/370/380/390501-1563 501-1564 501-1495 501-170324MB Parityw 1MB SIMMs8MB Parityw 1MB SIMMs48MB Parityw 1MB SIMMs32MB Parityw

Reference8 Mbyte, 24 Mbyte, and 48 Mbyte Parity Memory Board Installation and ConfigurationManual, 800-3403.Jumper Settings and Memory ConfigurationsJ

Power24MB4.3 Amps @ +5Vdc21.5 Watts48MB5.3 Amps @ +5Vdc26.5 WattsLast updated: December 2, 1996Comments and SuggestionsSun4/I: Memory - Sun 4300http:/

Sun 4400Sun-4/470/490501-1333 501-172132MB ECC 128MB ECCSun4/I: Memory - Sun 4400http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0

Power32MB15.6 Amps @ +5Vdc78.0 Watts128MB13.7 Amps @ +5Vdc68.5 WattsLED Status and Jumper SettingsMemory Board LEDsJumper SettingsJUMPER PINS SETTING

SunOS 4.1 PSR A requires 4.1 PSR A Sun-4 PMEG Patch to enable over 256MB of memory.3. A Correctable Error on the sixth 128MB board turns on the CE LE

Sun-4/E501-80424MB ECCJumper DescriptionsBOARD SIZESets the memory size of the board.BOARD IDDetermines where a memory board is mapped into the 256MBy

1M/4M DRAMSpecifies 1MByte or 4Mbyte DRAM modules.Jumper SettingsMemory Mapped into the Upper 256MBytes of Type 0 Address SpaceBOARDSIZEBOARDIDHI/LOWM

IEC 309 240 Volt Power ReceptacleLast updated: December 2, 1996Comments and SuggestionsSun4/II: Power - AC Sequencer Power Requirementshttp://lios.apa

Sun-4/E501-803616MB ECCJumper DescriptionsBOARD SIZESets the memory size of the board.BOARD IDDetermines where a memory board is mapped into the 256MB

1M/4M DRAMSpecifies 1MByte or 4Mbyte DRAM modules.Jumper SettingsMemory Mapped into the Upper 256MBytes of Type 0 Address SpaceBOARDSIZEBOARDIDHI/LOWM

Sun-4/E Combo501-80600MB ParityJUMPER SETTING DESCRIPTIONJ0401 InOutEnable MemoryDisable MemoryNoteSunOS 4.0.3e requires the 4.0.3e SRX Feature Tape t

ReferenceSPARCengine 1E Combo Memory Card User's Manual, 800-8152.Last updated: December 2, 1996Comments and SuggestionsSun4/I: Memory - Sun-4/E

CPUSun-4 ArchitectureSun 4100Sun 4200Sun 4300Sun 4400Sun-4e ArchitectureSPARCengine 1 (Sun-4/E)Last updated: December 2, 1996Comments and SuggestionsS

Sun 4100Sun 4/110/150501-1199501-1512501-1237501-1513501-1462501-15148MB w/o FP 8MB w FPC 16MB w/o FPC501-1463501-1515501-1464501-1516501-1465501-1517

Power: with FPU13.8 Amps @ +5Vdc0.1 Amps @ -5Vdc69.5 WattsSun 4100Sun 4/110/150501-1656 501-1657 501-16588MB w/o FPC 8MB w FPC 1 6MB w/o FPC 1501-1659

Power: with FPU13.8 Amps @ +5Vdc0.1 Amps @ -5Vdc69.5 Watts501-1199 / 501-1237 / 501-1462 / 501-1463 /501-1464 / 501-1465501-1512 / 501-1513 / 501-1514

* Default setting. The auto sense feature requires >=30 milliamps on the +12V return(example - DEC DELNI).NotesThe Type-4 Keyboard requires CPU >

Unused Pin 15-16 Out Out Out Out* Same/Different correspond to sets of 256KB or 1MB SIMMsSun 4100SIMM Configurations501-1314 501-1466256KB SIMM 1MB SI

115 Volt AC Power Sequencer300-1011Pulizzi Engineering PC874Outlet SideControl SideNotesRequires AC outlet NEMA L5-30R, 30A, 125V.1. Any conversion t

ReferenceSun 4100 Board Set Configuration Procedures, 813-2049.Last updated: December 2, 1996Comments and SuggestionsSun4/I: CPU - Sun 4100http://lios

Sun 4200Sun-4/260/280501-1274 501-1491 501-1522w FPC-6/4 w FPU-22-hi Backpanelw FPC-6/42-hi BackpanelPower17.2 Amps @ +5Vdc1.3 Amps @ -5VdcSun4/I: CPU

0.4 Amps @ +12Vdc98.0 WattsJumper SettingsJUMPER PINS SETTING DESCRIPTIONJ2701 1-2 Out Debug jumperJ2003 1-2 In Connect 3V batteryJ2201 1-2 In SCC (UA

Comments and SuggestionsSun4/I: CPU - Sun 4200http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00540.htm (3 von 3) [25.04.2002 16:2

Sun 4300Sun-4/310/330/350/360/370/380/390501-1316 501-17428MBw 1MB SIMMS32MBw 4MB SIMMSPower17.5 Amps @ +5vdc0.2 Amps @ +12vdc0.2 Amps @ -12vdcSun4/I:

92.3 WattsJumper SettingsJUMPER PINS SETTING DESCRIPTIONJ0200 1-23-45-6InInOutFPC normally lowFPC normally lowFPC normally highJ0900 1-2 In Enable Sys

4MB SIMMs, Option X134A, are not supported on the Sun-4/330 CPU.3. The Sun 4100 1MB SIMM, 501-1466, may be used in the Sun-4/310 and Sun-4/350 system

Sun 4400Sun-4/470/490501-1381 501-18990MB 0MBPower28.7 Amps @ +5Vdc0.1 Amps @ +12Vdc0.1 Amps @ -12Vdc145.9 WattsSun4/I: CPU - Sun 4400http://lios.apan

Jumper SettingsJUMPER PINS SETTING DESCRIPTIONJ0100 1-10 Out Used for debugJ0101 1-2 In Used for ATEJ0201 1-2 In Used for ATEJ0300 1-23-45-67-8InOutIn

NotesInstall Fused Shunt 150-1669-01 at locations J3603 and J3604 to provide circuit protection tothe M+ (+12Vdc) and M- (-12Vdc) inputs to the UC5170

ReferencesInstallation Manual for the Sun Full-height Rack System, 800-1555.1. Installation Manual for Sun Rackmountable Fileservers, 800-1556.2. Su

SPARCengine 1 (Sun-4/E)501-8035 501-8058 501-80644MBw Weitek4MBw/o Weitek16MBw WeitekPower5.0 Amps @ +5Vdc0.1 Amps @ +12Vdc0.1 Amps @ -12Vdc27.4 Watts

Jumper SettingsJUMPER PINS SETTING DESCRIPTIONJ0301 1-2 In 20MHz clock enableJ0801 1-22-3InInUse 4MB parity memory (default)Disable 4MB parity memoryJ

ConfigurationsSun PROM Monitor CommandsConfigurationsHandling Static Sensitive DevicesElectronic components on printed circuit boards can be damaged b

JumpersJumpers are used to connect two pins of a Terminal Strip. Two sizes of jumpers are used: 0.100 inchand 2.0 millimeter.Sun PROM Monitor Commands

Common EEPROM or NVRAM ParametersLocation 0x14 [Installed Memory]Amount of installed Memory in hexadecimalLocation 0x15 [Tested Memory]Amount of memor

Location 0x21 [Keyboard Click]00 = turns keyboard click OFF12 = turns keyboard click ON (default)Location 0x22 - 0x23 [Diagnostic Boot Device in ASCII

4800 baud 12 c09600 baud 25 80Location 0x63 [Serial Port B DTR/RTS]00 = asserts DTR and RTS signals02 = does not assert DTR and RTS signalsLocation 0x

230 Volt AC Power Sequencer370-1027 370-1155Pulizzi EngineeringPC874Pulizzi EngineeringPC874Outlet SideControl SideNotesRequires AC outlet NEMA L6-30R

ReferencesSun Full-Height Rack System Installation Manual, 800-1677.1. Sun Rackmountable Fileservers Installation Manual, 800-1676.2. Sun 900 Mbyte

240 Volt AC Power Sequencer370-1126 370-1156Pulizzi EngineeringPC874Pulizzi EngineeringPC874Outlet SideControl SideNotesRequires a Blue, IEC 309, 2-Po

Fuji PEX445-30575 Watt Power SupplySun-4/150/350300-1020Sun4/II: Power - Fuji PEX445-30 575 Watt Power Supplyhttp://lios.apana.org.au/~cdewick/sunshac

ReferencesSun Full-Height Rack System Installation Manual, 800-1677.1. Sun Rackmountable Fileservers Installation Manual, 800-1676.2. Sun 900 Mbyte

230 Volt AC Power Sequencer370-1155-02Sherwood EnterprisesOutlet SideControl SideNotesRequires AC outlet NEMA L6-30R, 30A, 250V.1. Any conversion to

Sun 56-inch Expansion Cabinet Installation Manual, 800-5936-18.5. Sun 56-inch Expansion Cabinet Service Manual, 800-6371-17.6. Last updated: Decembe

230 Volt AC Power Sequencer300-1263Sherwood EnterprisesOutlet SideControl SideNotesRequires AC outlet NEMA L6-30R, 30A, 250V.1. Any conversion to the

240 Volt AC Power Sequencer370-1156-03Sherwood EnterprisesOutlet SideControl SideNotesRequires a Blue, IEC 309, 2-Pole, 3-Wire, 32A, 250V AC receptacl

ReferencesSun Full-Height Rack System Installation Manual, 800-1677.1. Sun Rackmountable Fileservers Installation Manual, 800-1676.2. Sun 900 Mbyte

240 Volt AC Power Sequencer300-1264Sherwood EnterprisesOutlet SideControl SideNotesRequires a Blue, IEC 309, 2-Pole, 3-Wire, 32A, 250V AC receptacle.1

Power - IntroductionAC Power CordsFusesWire HarnessesSun 5-Slot Office Pedestal Wiring DiagramSun 12-Slot Office Pedestal Wiring DiagramSun 16-Slot Lo

AC Power CordsPART # DESCRIPTION USAGE180-1010 IEC 320 - Reverse IEC 320, Coiled (obs) Acc Pwr180-1117 IEC 320 - Reverse IEC 320 Acc Pwr180-1097 IEC 3

530-1657 90° IEC 320 - NEMA 5-15, 10A/125V, Grey USA530-1663 90° IEC 320 - CEE 7/7, 10A/250V, Grey France530-1663 90° IEC 320 - CEE 7/7, 10A/250V, Gre

Fuse15 Amps @ 250 VoltsLast updated: December 2, 1996Comments and SuggestionsSun4/II: Power - Fuji PEX445-30 575 Watt Power Supplyhttp://lios.apana.or

Last updated: December 2, 1996Comments and SuggestionsII: Power - AC Power Cordshttp://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00

FusesFUSE SIZE SUN PART # VENDOR PART #1/16A .25 x 1.25" 140-1004 Littelfuse 312.0621/16A .25 x 1.25" 140-1004 Bussman AGC 1/161/8A .25 x 1.

3A .25 x 1.25" 150-1034 Littelfuse 313 0033A PICO II 140-1038 Littelfuse 252 0033A .145 x .30" 140-1038 Bussman A3XRAD3A .25 x 1.25" 15

7A .25 x 1.25" 150-1258 Littelfuse 313 0077A .25 x 1.25" 150-1258 Bussman MDQ-78A .25 x 1.25" 140-1006 Littelfuse 314 0088A .25 x 1.25&

Holder, In Line 22-14AWG 140-1023 AMP 552844-1Holder, In Line 22-14AWG 140-1023 Littelfuse 155 020UHolder, UL/CSA/VDE 150-1041 Schurter FEU 031.1693Ho

PTCsPositive Temperature Coefficient (PTC) thermistors are resistors with a high positive temperaturecoefficient of resistance. The PTC is used as a s

Wire HarnessesWire Harness Color CodesThe most common wire insulation colors used on Sun AC and DC wire harnesses are shown in thecharts below. Not al

A non-TUV female faston does not attach to a TUV male faston. Use adapter harness 811-9015-01.Last updated: December 2, 1996Comments and SuggestionsII

Sun 5-Slot Office Pedestal Wiring DiagramSun-4/330 and SPARCserver 630MPLast updated: December 2, 1996Comments and SuggestionsII: Power - Sun 5-Slot O

Sun 12-Slot Office Pedestal Wiring DiagramSun-3/470, Sun-4/370, and Sun-4/470 shipped prior toAugust 1991Sun-4/470 and SPARCserver 670MP shipped after

Summit CS0325-9001325 Watt Power SupplySun-4/110/310300-1022Sun4/II: Power - Summit CS0325-9001 325 Watt Power Supplyhttp://lios.apana.org.au/~cdewick

Last updated: December 2, 1996Comments and SuggestionsII: Power - Sun 12-Slot Office Pedestal Wiring Diagramhttp://lios.apana.org.au/~cdewick/sunshack

Sun 16-Slot Logic Enclosure WiringDiagramSun-4/390 shipped prior to April 1990Sun-4/390, Sun-4/490, and SPARCserver 690MPshipped after April 1990II: P

Last updated: December 2, 1996Comments and SuggestionsII: Power - Sun 16-Slot Logic Enclosure Wiring Diagramhttp://lios.apana.org.au/~cdewick/sunshack

DiagnosticsSelf-Test DiagnosticDiagnostic Executive1.2 Diagnostic Executive (Sun-4)1.2 Diagnostic Executive (Sun-4s)1.6 Diagnostic Executive (Sun-4c)S

Self-Test DiagnosticThe CPU Self-Test runs in either the Normal or Diag mode. Set the CPU DIAG/NORM switch toDIAG or set the diag-switch? NVRAM parame

Diagnostic ExecutiveThe Diagnostic Executive (Exec) provides a single, unified diagnostic environment with one userinterface. The diagnostic tests res

1.2 Diagnostic ExecutiveSun-4Table of ContentsNAMEFILE(DECIMAL)DESCRIPTIONtpboot.sun4 0 Enables boot from tapeCopyright 1 Textfile containing copyrigh

tape4.exec 32 Pertec 1/2-inch Tape Diagnosticvideo4.exec 33 Sun Video Circuit Diagnosticvidmon4.exec 34 Sun Video Monitor Diagnosticvme4.exec 35 Sun V

1.2 Diagnostic Executive - Sun-4sSPARCsystems 300/400Table of ContentsNAME FILE DESCRIPTIONtpboot.sun4 0 Enables boot from tapeCopyright 1 Textfile co

smd4.exec 33 Sun SMD Diagnostictaac4.exec 34 TAAC Diagnostictape4.exec 35 Tape Diagnosticvme4.exec 36 VME Diagnosticnetcon4 37 NETCONlogfile 38 LOGFIL

Fuse7 Amps @ 250 VoltsNoteWait at least two minutes after power down or power outage before turning power ON to allowthe unit to reset.Last updated: D

1.6 Diagnostic ExecutiveSun-4cTable of ContentsNAME DESCRIPTIONexec4c Diag Exec for Sun-4c architecturediags4c Diagnostic Menu and File namescache4c.e

Sun Diagnostics 3.2Featuring: MPDiag and SunDiagnostic Executive 2.2SS600MP / SS10 / SS1000 /SC2000MPDiag tests the following components and functions

NotesSun Diagnostics 3.2 was released in July 1993.1. This is the last field release of the SunDiagnostic Executive.2. Last updated: December 2, 199

Loopback ConnectorsRS-232/RS-423PART # SYSTEM BOARDS CONNECT PINS540-1281-01 CPU,SCSI, and ALM 2-3 4-5 6-20540-1558-01 CPU, SCSI, ALM, ALM-2,MCP, and

370-1366-01540-1558-0196-Pin High-Density Loopback ConnectorRS-232/RS-423 Loopback Test PlugLast updated: December 2, 1996Comments and SuggestionsSun4

DiskSunOS 4.x SCSI TargetsSolaris 2.1 and 2.2 SCSI TargetsSolaris 2.3 SCSI TargetsSCSI Disk DrivesSingle-ended 8-bit SCSI PinoutsMedia Defect Manageme

SunOS 4.x SCSI TargetsSun-4/330 on SunOS 4.xSCSI DEVICE TARGET ID UNIX ID BOOT ID1st Internal Disk 3 sd6 sd(0,18,0)2nd Internal Disk 1 sd2 sd(0,8,0)1s

1st Tape2nd Tape3rd Tape4th TapeCD-ROM1st SCSI1st SCSI1st SCSI1st SCSI1st SCSI45326st0st1st2st3sr0*st(0,0,0)st(0,28,0)st(0,18,0)st(0,10,0)st(0,30,1)1s

Solaris 2.1 and 2.2 SCSI TargetsSolaris 2.1 and 2.2 allow any SCSI device to be assigned any Target number. This chart shows thedefault target numbers

33 231 - 234 235 - 236 23734 238 - 241 242 - 243 24435 245 - 248 249 - 250 25136 252 - 255 256 - 257 25837 259 - 262 263 - 264 26538 266 - 269 270 - 2