HP 720 Series Instalační příručka

HP E-MSM720 Controllers Installation GuideAbstractThis document describes how to install and initially configure the E-MSM720 Controllers. This docume

LED behaviorDuring the self test:• Initially, all the controller and port LEDs are on. Most of the LEDs turn off and then may turnon again during phas

1. Use a #1 Phillips (cross-head) screwdriver and attach the mounting brackets to the controllerwith the included 8 mm M4 screws.Figure 5 Attaching mo

2. Attach the controller to the wall or wood surface with two 15.9 mm (5/8 inch) number 12wood screws (not included).Figure 7 Wall mounting the contro

3. Secure the power cord to the controller with the provided cable tie.Figure 9 Securing the power cord to the controller1233. Cable tie anchor2. Cabl

The controller supports these mini-GBICs:• HP X112 100M SFP LC BX-D Transceiver J9099B• HP X112 100M SFP LC BX-U Transceiver J9100B• HP X111 100M SFP

Figure 10 Installing a mini-GIBIC2313. Wire bail2. Mini-GBIC1. Mini-GBIC SlotRemoving the mini-GBICsNOTE: You should disconnect the network cable from

3 Controller initial configurationPerform initial configurationNOTE: A factory-default controller is assumed. Ports 1 to 4 are available at 192.168.1.

5. Follow the Configure initial controller settings workflow.a. It is highly recommended that you follow the Configure initial controller settings wor

Review the settings before you select Apply to save and activate the new configurationon the controller. Alternatively, select Back to go to the previ

Configure basic guest access1. To configure basic guest access, follow the Create a wireless network for guests workflow.Select Start to launch this w

© Copyright 2011 Hewlett-Packard Development Company, L.P.The information contained herein is subject to change without notice. The only warranties fo

4. On the Guest DHCP addressing page, select DHCP server.a. Define the DHCP server IP address range:• Set Start address to 192.168.1.1• Set End addres

Verify the settings and then select Apply.7. After applying your changes, a confirmation page appears showing the menu paths to eachconfiguration page

Perform the verificationThis test uses your existing wired connection to controller port 1 (or any of 2/3/4) to test the publicaccess interface that i

4 Support and other resourcesOnline documentationYou can download documentation from the HP Support Website at: www.hp.com/support/manuals.Search by p

A SpecificationsPhysicalWeightHeightDepthWidth0.91 kg (2.25 lbs)4.4 cm (1.73 in)16.5 cm (6.5 in)25.4 cm (10 in)ElectricalFrequency rangeMaximum curren

• EFT/Burst: IEC 61000-4-4• Surge: IEC 61000-4-5• Conducted: IEC 61000-4-6• Power frequency magnetic field: IEC 61000-4-8• Voltage dips and interrupti

Category 5, 100-ohm 4-pair UTP or STP cable, complying with IEEE 802.3ab1000BASE-T specifications—Category 5e or better is recommended. See Noteon 100

B Mode conditioning patch cord (fiber cables)The following information applies to installations in which multimode fiber-optic cables are connectedto

C Regulatory informationFCC Class A NoticeOperation is subject to the following two conditions: This equipment has been tested and found tocomply with

European Community Declaration of ConformityEuropean Community Declaration of Conformity 29

Contents1 Identifying controller physical features...4Unpacking the controller...

D Recycle statementsWaste Electrical and Electronic Equipment (WEEE) statementsEnglish recycling noticeDisposal of waste equipment by users in private

Estonian recycling noticeÄravisatavate seadmete likvideerimine Euroopa Liidu eramajapidamistesSee märk näitab, et seadet ei tohi visata olmeprügi hulk

Italian recycling noticeSmaltimento di apparecchiature usate da parte di utenti privati nell'Unione EuropeaQuesto simbolo avvisa di non smaltire

Romanian recycling noticeCasarea echipamentului uzat de către utilizatorii casnici din Uniunea EuropeanăAcest simbol înseamnă să nu se arunce produsul

1 Identifying controller physical featuresUnpacking the controllerUnpack your controller and verify that you have received these items:• Controller• E

LEDsThere are three groupings of LEDs on the controller:• Status LEDs (Table 1 (page 5))• Port LEDs (Table 2 (page 5))• Port LED Mode indicator LEDs (

Figure 2 LED mode select button and LEDs1 3 423. Port Link LED1. LED Mode Select button4. Port Mode LED2. Mode Indicator LEDs (Act, FDx, Spd)Table 3 P

2 Installing the controllerWARNING!• For indoor use only. The controller, AC power adapter, and all connected cables are notdesigned for outdoor use.•

CAUTION:• Ensure all port covers are installed when the port is not in use.• There are no user-serviceable parts inside these products. Any servicing,

Figure 3 Connecting the power cordCAUTION: Use only the AC/DC power adapter and power cord supplied with the controller.Use of other adapters or power