HP 8100 - Elite Convertible Minitower PC Uživatelská příručka

Hardware Reference GuideHP Compaq 8100 Elite Convertible MinitowerBusiness PC and HP Z200 Convertible MinitowerWorkstation

Removing the Computer Access Panel1. Remove/disengage any security devices that prohibit opening the computer.2. Remove all removable media, such as c

Replacing the Computer Access Panel1. Lay the computer down on its large base for greater stability.2. Slide the lip on the front end of the access pa

Removing the Front Bezel1. Remove/disengage any security devices that prohibit opening the computer.2. Remove all removable media, such as compact dis

Removing Bezel Blanks1. Remove/disengage any security devices that prohibit opening the computer.2. Remove all removable media, such as compact discs

Replacing the Front BezelInsert the three hooks on the bottom side of the bezel into the rectangular holes on the chassis (1) thenrotate the top side

Installing Additional MemoryThe computer comes with double data rate 3 synchronous dynamic random access memory (DDR3-SDRAM) dual inline memory module

Installing DIMMsCAUTION: You must disconnect the power cord and wait approximately 30 seconds for the power todrain before adding or removing memory m

7. Open both latches of the memory module socket (1), and insert the memory module into the socket(2).Figure 7 Installing a DIMMNOTE: A memory module

Removing or Installing an Expansion CardThe computer has three standard full-height PCI expansion slots, one PCI Express x1 expansion slot,one PCI Exp

8. Before installing an expansion card, remove the expansion slot cover or the existing expansioncard.a. If you are installing an expansion card in a

© Copyright 2009 Hewlett-PackardDevelopment Company, L.P. Theinformation contained herein is subject tochange without notice.Microsoft, Windows, and W

c. If you are removing a PCI Express x16 card, pull the retention arm on the back of the expansionsocket away from the card and carefully rock the car

11. To install a new expansion card, slide the bracket on the end of the card down into the slot on theback of the chassis and press the card down fir

Drive PositionsNOTE: Your computer may look different than the illustration shown below.Figure 13 Desktop and Minitower Drive PositionsTable 1 Drive

Removing a Drive from a Drive BayCAUTION: All removable media should be taken out of a drive before removing the drive from thecomputer.1. Remove/dise

●If you are removing a media card reader, disconnect the USB cable from the system board.If the media card reader has a 1394 port, disconnect the 1394

7. Remove the drive from the drive bay as follows:●To remove a 5.25-inch drive in the desktop configuration, press down on the yellow drivelockmechani

●To remove a hard drive from and internal 3.5-inch drive bay, pull up on the green hard drivedrivelock mechanism (1) for that drive and slide the driv

Installing Additional DrivesWhen installing additional drives, follow these guidelines:●The primary Serial ATA (SATA) hard drive must be connected to

CAUTION: To prevent loss of work and damage to the computer or drive:If you are inserting or removing a drive, shut down the operating system properly

8. Install the drive in the desired drive bay by sliding it all the way into the front of the drive cage untilit locks (2). The drivelock automaticall

About This BookThis guide provides basic information for upgrading this computer model.WARNING! Text set off in this manner indicates that failure to

10. If you are installing a new drive, connect the opposite end of the data cable to the appropriatesystem board connector.NOTE: If you are installing

6. Install four 6-32 isolation mounting guide screws, two on each side of the drive.Figure 23 Installing the Hard Drive Guide ScrewsNOTE: The hard dr

8. Connect the power cable (1) and data cable (2) to the rear of the hard drive.Figure 25 Connecting the Power Cable and Data Cable to a SATA Hard Dr

2. Remove the screw from the rear of the carrier (1) and slide the top cover off the carrier (2).Figure 26 Removing the Carrier Cover3. Remove the ad

4. Remove the four screws from the bottom of the hard drive carrier.Figure 28 Removing the Security Screws5. Slide the hard drive back to disconnect

6. Place the new hard drive in the carrier then slide the hard drive back so that it seats in the SATAconnector on the carrier's circuit board. B

8. Place the thermal sensor on top of the hard drive in a position that does not cover the label (1) andattach the thermal sensor to the top of the ha

Changing from a Minitower to a Desktop Configuration1. Remove/disengage any security devices that prohibit opening the computer.2. Remove all removabl

9. Gently slide the drive into the uppermost available bay until it snaps into place. When the drive isproperly inserted, the drivelock will secure it

13. Reposition the subpanel (rotate it 90º), then snap it back into the bezel.NOTE: Your computer may look different than the illustration shown below

iv About This Book ENWW

Changing from a Desktop to a Minitower Configuration1. Remove/disengage any security devices that prohibit opening the computer.2. Remove all removabl

9. Gently slide the drive into the uppermost available bay until it snaps into place. When the drive isproperly inserted, the drivelock will secure it

13. Reposition the subpanel (rotate it 90º), then snap it back into the bezel.NOTE: Your computer may look different than the illustration shown below

Battery ReplacementThe battery that comes with the computer provides power to the real-time clock. When replacing thebattery, use a battery equivalent

Type 1a. Lift the battery out of its holder.Figure 42 Removing a Coin Cell Battery (Type 1)b. Slide the replacement battery into position, positive s

b. Insert the new battery and position the clip back into place.Figure 44 Removing a Coin Cell Battery (Type 3)NOTE: After the battery has been repla

Installing a Security LockThe security locks displayed below and on the following pages can be used to secure the computer.HP/Kensington MicroSaver Se

HP Business PC Security Lock1. Fasten the security cable by looping it around a stationary object.Figure 47 Securing the Cable to a Fixed Object2. Th

3. Screw the lock to the chassis using the screw provided.Figure 49 Attaching the Lock to the Chassis4. Insert the plug end of the security cable int

The front bezel can be locked in place by installing a security screw provided by HP. To install thesecurity screw:1. Remove/disengage any security de

Table of contentsHardware UpgradesWarnings and Cautions ...

8. Install the screw through the interior of the front of the chassis into the front bezel. The screw holeis located on the left edge of the chassis n

A Electrostatic DischargeA discharge of static electricity from a finger or other conductor may damage system boards or otherstatic-sensitive devices.

B Computer Operating Guidelines,Routine Care and Shipping PreparationComputer Operating Guidelines and Routine CareFollow these guidelines to properly

Optical Drive PrecautionsBe sure to observe the following guidelines while operating or cleaning the optical drive.Operation●Do not move the drive dur

IndexAaccess panellocking and unlocking 2removing 3replacing 5Bbattery replacement 37Cchanging computerconfiguration 31, 34computer operating guideli

Appendix B Computer Operating Guidelines, Routine Care and Shipping PreparationComputer Operating Guidelines and Routine Care ...

Hardware UpgradesWarnings and CautionsBefore performing upgrades be sure to carefully read all of the applicable instructions, cautions, andwarnings i

Unlocking the Smart Cover LockNOTE: The Smart Cover Lock is an optional feature included on some models only.The Smart Cover Lock is a software-contro

5. Use the Smart Cover FailSafe Key to remove the two tamper-proof screws that secure the SmartCover Lock to the chassis.NOTE: Your computer may look