HP ProDesk 400 G1 Base Small Form Factor PC Uživatelský manuál

Hardware Reference GuideHP ProDesk 400 G1 Small Form Factor

Media card reader componentsThe media card reader is an optional device available on some models only. Refer to the followingillustration and table to

Serial number locationEach computer has a unique serial number and a product ID number that are located on the exteriorof the computer. Keep these num

2 Hardware upgradesServiceability featuresThe computer includes features that make it easy to upgrade and service. No tools are needed formost of the

Removing the computer access panelTo access internal components, you must remove the access panel:1. Remove/disengage any security devices that prohib

Replacing the computer access panelPlace the panel on the computer (1) then slide it forward (2) and tighten the thumbscrew (3) to securethe panel in

Removing the front bezel1. Remove/disengage any security devices that prohibit opening the computer.2. Remove all removable media, such as compact dis

Removing bezel blanksOn some models, there are bezel blanks covering the 3.5-inch and slim optical drive bays that needto be removed before installing

Replacing the front bezelInsert the four hooks on the bottom side of the bezel into the rectangular holes on the chassis (1) thenrotate the top side o

Changing from desktop to tower configurationThe Small Form Factor computer can be used in a tower orientation with an optional tower stand thatcan be

System board connectionsRefer to the following illustration and table to identify the system board connectors for your model.No. System Board Connecto

© Copyright 2013 Hewlett-PackardDevelopment Company, L.P. Theinformation contained herein is subject tochange without notice.Microsoft® and Windows® a

Installing additional memoryThe computer comes with double data rate 3 synchronous dynamic random access memory (DDR3-SDRAM) dual inline memory module

●The system will operate in flex mode if the memory capacity of the DIMM in Channel A is notequal to the memory capacity of the DIMM in Channel B. In

7. Open both latches of the memory module socket (1), and insert the memory module into thesocket (2).NOTE: A memory module can be installed in only o

Removing or installing an expansion cardThe computer has three PCI Express x1 expansion slots and one PCI Express x16 expansion slot.NOTE: The PCI Exp

9. Before installing an expansion card, remove the expansion slot cover or the existing expansioncard.NOTE: Before removing an installed expansion car

c. If you are removing a PCI Express x16 card, pull the retention arm on the back of theexpansion socket away from the card and carefully rock the car

12. To install a new expansion card, hold the card just above the expansion socket on the systemboard then move the card toward the rear of the chassi

18. Lock any security devices that were disengaged when the access panel was removed.19. Reconfigure the computer, if necessary.Drive positions1 Slim

Installing and removing drivesWhen installing drives, follow these guidelines:●The primary Serial ATA (SATA) hard drive must be connected to the dark

CAUTION: To prevent loss of work and damage to the computer or drive:If you are inserting or removing a drive, shut down the operating system properly

About This BookThis guide provides basic information for upgrading the HP ProDesk Business PC.WARNING! Text set off in this manner indicates that fail

Removing a 3.5-inch deviceCAUTION: All removable media should be taken out of a drive before removing the drive from thecomputer.1. Remove/disengage a

8. Disconnect the drive cables from the rear of the drive, or, if you are removing a media cardreader, disconnect the USB cable from the system board

Installing a 3.5-inch device1. Remove/disengage any security devices that prohibit opening the computer.2. Remove all removable media, such as compact

9. Rotate the drive cage to its upright position.10. Slide the device into the drive bay, making sure to align the guide screws with the guide slots,u

11. If installing a USB 3.0 media card reader, you must use the USB 3.0 to USB 2.0 adapter andconnect the adapter cable from the media card reader to

16. Reconnect the power cord and any external devices, then turn on the computer.17. Lock any security devices that were disengaged when the access pa

Installing a slim optical drive1. Remove/disengage any security devices that prohibit opening the computer.2. Remove all removable media, such as comp

9. Slide the optical drive through the front bezel all the way into the bay so that it locks in place (1),then connect the power and data cables to th

5. If the computer is on a stand, remove the computer from the stand.6. Remove the computer access panel.7. Disconnect the power cable (1) and data ca

9. To install a hard drive, you must transfer the silver and blue isolation mounting guide screwsfrom the old hard drive to the new hard drive.10. Ali

iv About This Book

11. Connect the power cable (1) and data cable (2) to the back of the hard drive.NOTE: The data cable for the primary hard drive must be connected to

Removing a 2.5-inch hard drive1. Remove/disengage any security devices that prohibit opening the computer.2. Remove all removable media, such as compa

8. Disconnect the power cable (1) and data cable (2) from the back of the hard drive.9. Pull outward on the release lever at the rear of the drive (1)

Installing a 2.5-inch hard drive1. Remove/disengage any security devices that prohibit opening the computer.2. Remove all removable media, such as com

8. Rotate the drive cage to its upright position.9. Align the guide screws on the drive with the J-slots on the sides of the drive bay. Press the driv

10. Connect the power cable (1) and data cable (2) to the back of the hard drive.NOTE: If the 2.5-inch hard drive is the primary drive, connect the da

Installing a security lockThe security locks displayed below and on the following pages can be used to secure the computer.Cable lockPadlock40 Chapter

HP business PC security lock1. Fasten the security cable by looping it around a stationary object.2. Insert the cable lock into the cable lock slot on

3. Slide the security cable through the hole in the cable lock on the rear of the monitor.4. Use the bracket provided in the kit to secure other perip

5. Thread the keyboard and mouse cables through the computer chassis lock.6. Unscrew the thumbscrew that secures the access panel to the chassis (1) a

Table of contents1 Product features ...

7. Screw the lock to the chassis in the thumbscrew hole using the screw provided.8. Insert the plug end of the security cable into the lock (1) and pu

9. When complete, all devices in your workstation will be secured.Installing a security lock 45

Front bezel securityThe front bezel can be locked in place by installing a security screw provided by HP. To install thesecurity screw:1. Remove/disen

8. Install the security screw through the middle front bezel release tab to secure the front bezel inplace.9. Replace the access panel.10. If the comp

A Battery replacementThe battery that comes with the computer provides power to the real-time clock. When replacing thebattery, use a battery equivale

7. Depending on the type of battery holder on the system board, complete the following instructionsto replace the battery.Type 1a. Lift the battery ou

b. Insert the new battery and position the clip back into place.NOTE: After the battery has been replaced, use the following steps to complete this pr

B Electrostatic dischargeA discharge of static electricity from a finger or other conductor may damage system boards or otherstatic-sensitive devices.

C Computer operating guidelines, routinecare and shipping preparationComputer operating guidelines and routine careFollow these guidelines to properly

Optical drive precautionsBe sure to observe the following guidelines while operating or cleaning the optical drive.Operation● Do not move the drive du

Installing a security lock ... 40Cab

IndexAaccess panelremoval 7replacement 8Bbattery replacement 48Ccomputer operating guidelines 52DDIMMs. See memorydrivescable connections 22installati

1 Product featuresStandard configuration featuresFeatures may vary depending on the model. For a complete listing of the hardware and softwareinstalle

Front panel componentsDrive configuration may vary by model. Some models have a bezel blank covering one or more drivebays.1 Slim Optical Drive (optio

Rear panel components1 PS/2 Mouse Connector (green) 6 Power Cord Connector2RJ-45 Network Connector 7 PS/2 Keyboard Connector (purple)3Serial Connect