HP StorageWorks 20 - Modular Smart Array Specifikace Strana 53
- Strana / 84
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Replacing a 2-P
ort Ethernet iSCSI module
Before you begin
CAUTION:
• Before removing a component or blank from an operational device, make sure that you have the
replacement part or blank available. Removing a component or blank impacts the airflow pattern
and cooling ability of the device. Allow approximately 30 seconds before installing the new or
replacement component to ensure that configuration data about the removed component is cleared
from the system registry, but, to avoid possible overheating, insert the new or replacement component
withinoneortwominutes.Iftheinternaltemperatureexceedsacceptablelimits,thedevicemay
overheat and automatically shut down or restart.
• Parts can be damaged by electrostatic discharge. Use proper anti-static protection.
CAUTION:
• In dual-controller configurations, hot-add or hot-replace a controller or 2-Port Ethernet iSCSI module
only during periods of low I/O. Hot-adding or hot-replacing these modules while under heavy I/O
may cause a momentary pause, performance decrease, or loss of access to the MSA while the new
controller is starting up. After the startup process is complete, full functionality will be restored.
• In dual-controller configurations, the MSA controller and 2-Port Ethernet iSCSI modules are
hot-pluggable and the MSA does not need to be powered down during the replacement. However,
you must first use an MSA management utility, such as the SMU or MSA-CLI to disable the controller
before removal.
Verifying component failure
Before replacing the 2-Port Ethernet iSCSI module:
• Verify that the 2-Port Ethernet iSCSI module status LED is off or is flashing amber.
• Check the array controller LCD display panel for error messages and take appropriate action.
Remov
ing the 2-Port Ethernet iSCSI I/O module
CAUTION:
Stop all system access to the module before proceeding with these replacement procedures.
1. Review all warnings, cautions, and preparation procedures as detailed in Warnings and precautions.
2. Disconnect the cable from the 2-Port Ethernet iSCSI module.
1510i Modular Smart Array maintenance and service guide
53
- HP StorageWorks 1
- Contents 3
- About this guide 7
- Document c 8
- Rack stability 9
- HP technical support 9
- Customer self repair 9
- Subscription service 9
- HP websites 9
- Documentation feedback 10
- 1 Illustrated parts list 11
- 2Specifications 13
- Chassis specifi 14
- Fan module spec 15
- SCSI I/O module specifications 15
- Power sup 15
- Specifications 16
- 3 System components and LEDs 17
- Rear view 18
- Chassis and com 19
- Controller LEDs 20
- Hard drive LEDs 21
- SATA hard drive 23
- Slot diagram LE 24
- The 2-Port Ethe 25
- Fan module LEDs 26
- SCSI I/O module LEDs 27
- Power supply module LEDs 28
- 4 Available diagnostic tools 29
- Available diagnostic tools 30
- 5 Customer replaceable 31
- Customer self 32
- Recommended to 33
- Warnings and precautions 33
- Equipment symbols 34
- Weight warning 35
- Rack warnings and precautions 35
- Determinin 37
- Powering off the MSA 38
- Powering on the MSA 39
- Removing or inst 40
- Removing or ins 41
- Replacing a har 42
- Verifying component failure 43
- Removing the hard drive 43
- Installing the hard drive 44
- Replacing the c 46
- Removing the controller 47
- Installing the controller 52
- Verifying proper operation 52
- Replacing a 2-P 53
- Replacing a fan 55
- Replacing a SCS 57
- II/Omodule 57
- Replacing a pow 59
- Installing the p 60
- Replacing the M 61
- SA1510i chassis 61
- Prepareforthereplacement 62
- Remove the fan modules 62
- Remove the SCSI I/O modules 63
- Remove the controllers 63
- Remove the MSA from the rack 64
- Record th 64
- Install the MSA in the rack 64
- Install the controllers 65
- Install the SCSI I/O modules 66
- Install the fan modules 66
- Completing the replacement 67
- A Regulatory compliance and 69
- Laser compliance 70
- International n 71
- Japanese notice 72
- Korean notice (A&B) 72
- Battery Replacement notice 73
- Power cords 73
- Japanese Power Cord notice 73
- Electrostatic d 74
- Czechoslovakian notice 74
- Danish notice 75
- Dutch notice 75
- English notice 75
- Estonian notice 75
- Finnish notice 76
- French notice 76
- German n 76
- Greek notice 76
- Hungarian notice 77
- Italian notice 77
- Latvian notice 77
- Lithuanian notice 78
- Polish notice 78
- Portuguese notice 78
- Slovakian notice 78
- Slovenian notice 79
- Spanish notice 79
- Swedish notice 79
Související produkty a manuály pro Barebones pro PC / pracovní stanice HP StorageWorks 20 - Modular Smart Array
Barebones pro PC / pracovní stanice HP LH4r - NetServer - 256 MB RAM Technické informace
(158 stránky)
(158 stránky)
Barebones pro PC / pracovní stanice HP Z600 - Workstation - 6 GB RAM Rychlé specifikace
(80 stránky)
(80 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.029 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce