HP ZBook 14 Mobile Workstation Uživatelský manuál

Hardware Reference GuideHP t620 Flexible Series Thin Client

Using the keyboard(1) Caps Lock key Activates/deactivates the Caps Lock feature.(2) Scroll Lock key Activates/deactivates the Scroll Lock feature.(3)

Windows Logo KeyUse the Windows Logo Key in combination with other keys to perform certain functions available inWindows operating systems.Windows Log

Serial number locationEvery thin client includes a unique serial number located as shown in the following illustration. Havethis number available when

2 Hardware changesWarnings and cautionsBefore performing upgrades be sure to carefully read all of the applicable instructions, cautions, andwarnings

Connecting the power cord1. Plug the female end of the power cord into the power supply brick (1).2. Connect the other end of the power cord to an ele

Attaching the standCAUTION: The computer must be operated with the stand attached to ensure proper airflow aroundthe computer.The computer can be used

6. Reconnect the external equipment, plug the power cord into a power outlet, and then turn thecomputer on.NOTE: Be sure that at least 10.2 centimeter

4. Disconnect the power cord from the power outlet, and disconnect any external devices.CAUTION: Regardless of the power-on state, voltage is always p

Replacing the access panelTo replace the access panel:1. Position the access panel (1) on the chassis, approximately 6 mm (.24 in) inside the edge of

3. Insert the hooks on the right side of the I/O panel (1) into the right side of the back of thechassis, and then press the left side (2) to the chas

© Copyright 2013 Hewlett-PackardDevelopment Company, L.P. Theinformation contained herein is subject tochange without notice.Microsoft and Windows are

Installing internal USB flash drivesThere are two USB flash drive ports on the system board.To install a USB flash drive:1. Remove/disengage any secur

(1) USB-1 portUSB 2.0 flash drive: maximum dimensions 55mm (L) x 16 mm (W) x 8 mm (H)(2) USB-2 portUSB 2.0 flash drive: maximum dimensions 65mm (L) x

12. Replace the computer stand.13. Reconnect the power cord and turn on the computer.14. Lock any security devices that were disengaged when the compu

Populating SODIMM socketsThere are two SODIMM sockets on the system board. The sockets are labeled DIMM1 and DIMM2.Item Description System Board Label

3. Turn off the computer properly through the operating system, and then turn off any externaldevices.4. Disconnect the power cord from the power outl

8. Locate the memory compartment on the system board.9. If a fiber NIC is installed, move the cable carefully out of the slot in the memory compartmen

12. To remove a SODIMM, press outward on the two latches (1) on each side of the SODIMM,rotate the SODIMM up (2), and then pull the SODIMM out of the

14. Hold the memory compartment cover with the fiber NIC slot toward the front of the computer,and then set the memory compartment cover (1) over the

20. Reconnect the power cord and turn on the computer.21. Lock any security devices that were disengaged when the computer cover or access panel wasre

Installing a half-height PCI-Express 2.0 cardYou may install an optional half-height PCI-Express (PCIe) card in the HP t620 PLUS Thin Client. Ariser c

About This BookWARNING! Text set off in this manner indicates that failure to follow directions could result in bodilyharm or loss of life.CAUTION: Te

8. Locate the slot in the riser card.9. Slide the expansion slot cover left and remove it.24 Chapter 2 Hardware changes

10. Align the PCIe card connectors with the slot in the riser card and the metal tab at the end of thecard with the slot in the chassis. Press the PCI

SecurityThe thin client is equipped with a hood sensor. You may also use a cable lock to secure thecomputer.For an additional layer of security, you m

Cable lockThese thin clients are designed to accept a security cable lock. This cable lock prevents unauthorizedremoval of the thin client, as well as

Mounting the thin clientHP t620 Thin Client: HP recommends mounting the thin client in the vertical (tower) orientation, withthe HP logo right-side up

2. Using four 15 mm screws included in the mounting device kit, attach one side of the HP QuickRelease to the thin client as shown in the following il

4. Slide the side of the mounting device attached to the thin client (1) over the other side of themounting device (2) on the device on which you want

Supported mounting optionsThe following illustrations demonstrate some of the supported mounting options for the mountingbracket.Mounting the thin cli

A SpecificationsFor the latest specifications or additional specifications on the HP t620 Thin Client or the HP t620PLUS Thin Client, go to http://www

Maximum Altitude (unpressurized)Operating(max. allowed rate of change is 457m per minute or 1500ft per minute)Nonoperating(max. allowed rate of change

iv About This Book

B Removing and replacing the batteryWARNING! Before removing the side access panel, be sure that the thin client is turned off and thepower cord is di

7. If the computer is an HP t620 PLUS Thin Client, perform the following steps:a. Push the fan assembly latch (1) toward the front of the computer and

8. Locate the battery on the system board.9. Carefully pry the battery up from the system board.10. Unplug the battery cable connector from the system

c. If a PCIe card was installed, reinstall it. For instructions, see Installing a half-height PCI-Express 2.0 card on page 23.d. Rotate the fan assemb

C Thin client operationCAUTION: Ensure that the write filter is enabled after committing necessary configurations to thethin client flash drive. Durin

Supported orientationsHP supports the following orientations for the thin client.CAUTION: You must adhere to HP-supported orientations to be sure that

40 Appendix C Thin client operation

Non-supported orientationHP does not support the following orientations for the thin client.CAUTION: Non-supported placement of thin clients could res

D Electrostatic dischargeA discharge of static electricity from a finger or other conductor may damage system boards or otherstatic-sensitive devices.

E Shipping informationShipping preparationFollow these suggestions when preparing to ship the thin client:1. Turn off the thin client and external dev

Table of contents1 Product features ...

4. Disconnect the power cord from the power outlet, and disconnect any external devices.CAUTION: Regardless of the power-on state, voltage is always p

9. Carefully pull the SSD out of the socket.Store the SSD carefully until it can be installed in the returned computer.10. Rotate the fan assembly dow

IndexAaccess panelremoving 10replacing 12altitude specifications 33Bbattery, replacing 34Ccable lock 27cable lock slot 3cautionsattaching the stand 9d

rear panel components 3recycling 37relative humidity specifications32removingaccess panel 10battery 34flash memory 43solid state drive 43SSD 43replaci

Appendix B Removing and replacing the battery ... 34Appendix C

1 Product featuresStandard featuresThank you for purchasing an HP thin client. We hope you have years of use from our thin clients. Ourgoal is to prov

CAUTION: Ensure that the write filter is enabled after committing necessary configurations to thethin client flash drive. During normal operation of t

Rear panel componentsFor more information, go to http://www.hp.com and search for your specific thin client model to findthe model-specific QuickSpecs