Hp 600 Modular Disk System Uživatelský manuál

HP StorageWorks 600 Modular Disk System User Guide Abstract This guide describes identification, operations, setup, configuration and utilities, tro

Component identification 10 Device bay ID numbers SAS and SATA hard drive LEDs Item Description 1 Fault/UID LED (amber/blue) 2 Online LED (gree

Component identification 11 SAS and SATA hard drive LED combinations Online/activity LED (green) Fault/UID LED (amber/blue) Interpretation On,

Operations 12 Operations Important Safety Information Before installing this product, read the Important Safety Information document provided. F

Operations 13 To power up the MDS600: 1. Complete server hardware installation and cabling. See the server blade documentation. 2. Connect the SAS

Setup 14 Setup Space and airflow requirements To allow for servicing and adequate airflow, observe the following space and airflow requirements when

Setup 15 performs an emergency shutdown of the hard drive bays within a drawer if the temperature exceeds this limit for greater than 3 minutes. To

Setup 16 Rack warnings WARNING: To reduce the risk of personal injury or damage to the equipment, be sure that: • The leveling jacks are extend

Setup 17 CAUTION: Always plan the rack installation so that the heaviest item is on the bottom of the rack. Install the heaviest item first, and c

Setup 18 WARNING: The HP MDS600 Disk System is very heavy. To reduce the risk of personal injury or damage to the equipment: • Observe local occ

Setup 19 • Hard drives are sensitive to excess vibration. Use care when opening and closing the drawer. • A RAID 1 mirror requires an even number

© Copyright 2009, 2011 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warr

Setup 20 CAUTION: To prevent improper cooling and thermal damage, do not operate the MDS600 for an extended period of time with the drawer open.

Setup 21 6. Install the hard drive. WARNING: Pinch hazard—Keep hands out of front and rear of chassis when closing hard drive drawers. 7. Wh

Setup 22 6. Push the I/O handle up. Be sure the I/O module is fully seated and the I/O module handle is in the locked position. CAUTION: For be

Setup 23 For a complete list of supported cables, see the QuickSpecs on the HP website (http://www.hp.com/go/mds600). Power cords The power cord sh

Configuration and utilities 24 Configuration and utilities Configuration tools Array Configuration Utility NOTE: ACU does not support mixing SA

Configuration and utilities 25 Smart Components for ROM Flash To update the firmware on the server, controller, hard drives, or enclosure use Smart

Configuration and utilities 26 • From within Survey Utility • From within operating system-specific IML viewers o For NetWare: IML Viewer o For

Configuration and utilities 27 Keeping the system current Change control and proactive notification HP offers Change Control and Proactive Notificat

Troubleshooting 28 Troubleshooting When the MDS600 does not power up If the MDS600 does not power up: 1. Ensure that the MDS600 is connected to a w

Troubleshooting 29 Issue Possible reasons Possible solutions I/O LED is amber • The I/O module might not be inserted properly, it might have a da

Contents 3 Contents Component identification ...

Troubleshooting 30 Status code Action 9 = Standby heartbeat failure Replace the I/O module that has an amber LED. If no I/O module has an amber LED

Troubleshooting 31 CAUTION: When fault tolerance is compromised, data loss can occur. However, it may be possible to recover the data. For more in

Troubleshooting 32 • Do not remove a second drive from an array until the first failed or missing drive has been replaced and the rebuild process i

Troubleshooting 33 Failure of another drive during rebuild If a non-correctable read error occurs on another physical drive in the array during the

Regulatory compliance notices 34 Regulatory compliance notices Regulatory compliance identification numbers For the purpose of regulatory compliance

Regulatory compliance notices 35 • Hewlett-Packard Company P. O. Box 692000, Mail Stop 530113 Houston, Texas 77269-2000 • 1-800-HP-INVENT (1-800-4

Regulatory compliance notices 36 • Hewlett-Packard Company P. O. Box 692000, Mail Stop 510101 Houston, Texas 77269-2000 • 1281-514-3333 To identi

Regulatory compliance notices 37 For non-telecommunications products and for EU harmonized telecommunications products, such as Bluetooth® within po

Regulatory compliance notices 38 Japanese notice BSMI notice Korean notice Class A equipment Class B equipment

Regulatory compliance notices 39 Chinese notice Class A equipment Vietnam compliance marking notice This marking is for applicable products only.

Contents 4 Change control and proactive notification ... 27 C

Electrostatic discharge 40 Electrostatic discharge Preventing electrostatic discharge To prevent damaging the system, be aware of the precautions yo

Specifications 41 Specifications Environmental specifications Specification Value Temperature range* Operating 10°C to 35°C (50°F to 95°F) M

Technical support 42 Technical support Before you contact HP Be sure to have the following information available before you call HP: • Technical su

Technical support 43 • Optional—Parts for which customer self repair is optional. These parts are also designed for customer self repair. If, howev

Technical support 44 Riparazione da parte del cliente Per abbreviare i tempi di riparazione e garantire una maggiore flessibilità nella sostituzione

Technical support 45 CSR-Teile werden abhängig von der Verfügbarkeit und vom Lieferziel am folgenden Geschäftstag geliefert. Für bestimmte Standorte

Technical support 46 Para obtener más información acerca del programa de Reparaciones del propio cliente de HP, póngase en contacto con su proveedor

Technical support 47 Opcional – Peças cujo reparo feito pelo cliente é opcional. Essas peças também são projetadas para o reparo feito pelo cliente.

Technical support 48

Technical support 49

Component identification 5 Component identification Front panel components Item Description 1 Drawer 1 2 Drawer 1 diagnostic cable access (For us

Acronyms and abbreviations 50 Acronyms and abbreviations ACU Array Configuration Utility ADG Advanced Data Guarding (also known as RAID 6) ADU Arr

Index 51 7 7-segment display 29 A ACU (Array Configuration Utility) 24 ADU (Array Diagnostic Utility) 26 airflow requirements 14 authorized

Index 52 J Japanese notice 38 K Korean notices 38 L LED behavior 28 LED, 7-segment display 8 LED, heartbeat 6, 8 LED, system fault 6, 8

Component identification 6 Front panel LEDs and button Item Description Status 1 Hard drive LEDs Normal mode (UID LED is solid) Green = The driv

Component identification 7 Item Description Status 1 Hard drive LEDs Drive locate mode (UID LED is flashing) Green = The drive has been selected b

Component identification 8 Item Description 2 Power On/UID 2 status panel 3 Fan module 1 (Drawer 2) 4 Primary I/O module (Drawer 2) 5 SAS port 1 co

Component identification 9 Item Description Status 2 Internal Health LED Green = System health is good. Off = System is off. 3 GSI LED* Amber =