HP tc2120 Server Instalační příručka

HP Server tc2120 Network Operating System Installation Guide For: Microsoft® Windows® 2000 Server and SP3 Microsoft Windows 2000 Server and Micros

2. Insert your HP Startup CD in a Windows PC and follow the on-screen instructions to create the Windows 2000 SCSI driver diskette (HP disk W2K SCSI

c. Press Enter to continue. d. Select the WIN2000 Promise FastTrack100 TX2™ Controller adapter, then press Enter. 4. Press Enter to continue at t

NOTE: The network settings may need to be customized to your environment. Refer to Microsoft 2000 manuals should you need further details on networ

— If you have access to a PC connected to the internet and equipped with a CD-RW drive, you may download the latest Service Pack from Microsoft at:

8. Click Finish once the LAN driver has been loaded. 9. Exit all open windows and restart your computer in order to properly initialize the LAN ada

c. Locate the "Digital Signer:" If the driver of that device is digitally signed then it will display "MS Windows 2000 Publisher"

5. Format all partitions that are not already formatted. 6. Exit the "Computer Management" tool. NOTE: There are two types of hard-driv

2. Select the appropriate client type for your environment. 3. Click Format disk if needed. Check the number of disks required and label them as &

1. Right click My Network Places | Properties | Local Area Connection on your HP server. NOTE: If your HP server hosts several network adapters,

From one of the clients, open a command prompt and type: ping computername where computername is the server name you entered during Windows 2000 i

© 2003 Hewlett-Packard Development Company, L.P. Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation. Intel and Pentium ar

NOTE: The following instructions correspond to the standard steps for new domain creation. You may customize the options proposed by Windows 2000 t

20. Configuring active directory display shows again. Click Finish to close the Wizard utility. This completes the active directory installation. 21

Tip #1. Windows 2000 Installation Halts about Three Minutes after Starting to Boot from CD-ROM When installing Windows 2000 on any X86 system with mo

Tip #2. Configure the Parallel (LPT) Port for ECP Mode The device manager may not show this port on the list when not configured in ECP mode. HP reco

Tip #4. Windows 2000 Recovery Options In the event that the current installation of Windows 2000 fails to boot (this might happen after installing a

Recovery option #3: Recovery Console (RC) Boot The Recovery Console (RC) can be used when safe boot fails. You can enter RC: • Either by booting fro

2. Open a command prompt, and type D:\I386\WINNT32 /CMDCONS (Where D: is the CD-ROM drive letter) 3. Follow the screen instructions to complete th

Installing Microsoft Windows Server 2003 Prepare the Installation Please refer to the Chapter 1 "Preparing the HP Server tc2120 for NOS Installa

10. On boot, press Crtl-F to enter the IDE RAID Configuration Utility and configure the IDE array as usual. Please refer to the Fast Track 100 Refe

4. If you are installing to the Promise FastTrak100 TX2 IDE RAID card do the following, if not skip to step 5: a. Press S to specify additional IDE

Contents Preparing the HP Server tc2120 for NOS Installation... 7 Section 1. Hardware Setup ...

a. Press C to create a partition. b. At the "Create partition size" prompt, type 4096 and press Enter. c. HP recommends that you create

NOTE: You may open the Manage Your Server wizard at any point in time by clicking Start | Programs | Administrative Tools | Manage Your Server. Se

Example: Installing the Embedded Compaq NC7760 Gigabit Server Adapter Driver 1. Insert one blank, formatted 3.5" diskette into a workstation&ap

Section 4. Configure the System Phase 1 – Perform Hardware Status Check In this section, you will run the Windows Device Manager tool to identify any

Phase 2 – Initialize Hard Disk Drive NOTE: There are two types of hard drive configurations: Dynamic and Basic. You can select the appropriate type

4. Click OK to continue, and then OK again to exit the "Local Area Connection Properties" window. Phase 2 – Attach Clients to Network and

Phase 3 – Domain Controller Setup In order to promote your server to a domain controller, proceed with the following: 1. Click Start | Administrat

14. Click Next to accept the "Database and Log Locations" default directories. 15. Click Next to accept the default "Shared System V

• Compaq 2100S SCSI RAID Controller • HP Modem v92 56k PCI Please refer to the product manual enclosed with your accessory for the detailed install

Tip #2. Windows Server 2003 Recovery Options In the event that the current installation of Windows Server 2003 fails to boot (this might happen after

Installing Microsoft Windows Server 2003... 27 Prepare the Installation ...

Recovery option #3: Recovery Console (RC) Boot The Recovery Console (RC) can be used when safe boot fails. You can enter RC: • Either by booting fro

Installing RC 1. Insert the Windows Server 2003 CD-ROM. If CD-ROM auto-start is enabled, click exit to close the applet. 2. Open a command prompt,

ASR Restore mode: 1. Boot from the Windows Server 2003 CD-ROM. 2. When prompted during the text mode portion of setup, press F2 to initiate Automat

Installing Novel NetWare 5.1 Prepare the Installation Please refer to the Chapter 1 "Preparing the HP Server tc2120 for NOS Installation" f

4. Create the third diskette for Novell 5.1 patch (HP disk NW patch). Choose the correct link for your OS language version: — For an English-only v

3. From the drive A: prompt, format and transfer DOS system files to the hard disk DOS boot partition by entering one of the following commands: —

Phase 2 – Install HP Drivers 1. The installation program then detects your hardware and attempts to match the drivers to the hardware. It displays a

4. The next Driver names summary screen displays storage and network devices. You need to manually install the HP LAN driver: a. Scroll down to cho

NOTE: It is possible that during the initial reboot of the NetWare 5.1 OS, the GUI mode may not load properly. This can be resolved by intalling NW

12. Press F10 to accept the default installation options. NOTE: If you want to be able to uninstall the Suport Pack later, you must select the op

Section 1. Run HP DiagTools (Optional)... 50 Section 2. Create the Drivers Disk

On-Line Information and Software Sources • HP World Wide Web access: http://www.hp.com • Novell World Wide Web access: http://www.novell.com • Nov

Section 2. Create the Drivers Diskettes 1. Locate one blank, formatted 3.5" diskette. 2. Insert your HP Startup CD in a Windows PC and follow

5. If you accept erasing all data on your disk, select Continue. Then press any key for your system to create the partition, reboot, and format that

NOTE: Do not remove the IDEATA driver, because it is used by the CD-ROM drive. d. Insert HP driver diskette (created with the Startup CD) in the f

4. Wait while the system loads the new drivers. 5. Review the Volume SYS and Partition Properties Screen. Select Modify if any changes are necessa

10. Click Next to validate the NDS summary. 11. Click Next at the Licenses window to install the license previously detected. 12. If you wish to i

3. At the system console prompt enter the command: load cdrom 4. Wait for about 15 seconds for the CD to be automatically mounted as a volume.

17. Select Edit STARTUP.NCF file and press Enter. 18. Add the full path to each driver displayed that was copied in the c:\drivers directory. (for

Troubleshooting Tip #1. Restarting NetWare Installation If you want to restart NetWare installation from the very beginning, use a utility such as fd

3. Install additional HP accessories. Section 1. Create the Drivers Diskettes 1. Locate one blank, formatted 3.5" diskette. 2. Insert your HP

1.1 Booting... 72 1.2 Installation Sett

• Phase 3 – Install HP Drivers • Phase 4 – Configure the Network PHASE 1 – Pre-Installation • If you are using a Non-bootable Installation CD or

Phase 1b – (Bootable Non-Multilingual Installation CD) NOTE: If your hard drive contains data or is not new, HP recommends using a utility such as

10. When the system comes up, press F10 to accept the license agreement. 11. Proceed to Phase 2 to continue. Phase 2 – Start the Installation 1. C

c. The installation program displays the drivers detected: a SCSI driver and a generic ATA/IDE/ATAPI Adapter driver (IDEATA.HAM). Press Delete to r

5. Wait while system loads the new drivers. 6. Review the Volume SYS and Partition Properties Screen. Select Modify if any changes are necessary,

10. Click Next to validate the NDS summary. 11. Click Next at the Licenses window to install the license previously detected. 12. If you wish to

Section 3. Install Additional HP Accessories The HP server tc2120 Startup CD includes the drivers for the following HP accessories: • HP-Intel 10/10

Installing Red Hat Linux 9.0 Prepare the Installation Please refer to the Chapter 1 “Preparing the HP Server tc2120 for NOS Installation” for our rec

Phase 2 — Configure the Server Welcome to Red Hat Linux Click on Next to continue. NOTE: Using the GUI installation, you will have an on-screen des

NOTE: If you get a message that says, “The partition table on device xyz was unreadable… click Yes as many times as this message pops up. Boot Load

Preparing the HP Server tc2120 for NOS Installation Section 1. Hardware Setup Prepare your HP server following the instructions in the HP Server tc21

Language Support Selection • Review the Language Support setting and modify if necessary. Time Zone Selection • Review and modify as necessary. Acc

Video Configuration • Red Hat will detect your chip as an ATI Mach64 chip. However, the HP Server tc2120 ships with an ATI Rage XL AGP chipset. Modi

• Red Hat World Wide Web access: http://www.redhat.com Installing Red Hat Linux 8.0 Prepare the Installation Please refer to the Chapter 1 “Preparin

2. At the "Keyboard Configuration" screen, select U.S. English and click Next. 3. At the "Mouse Configuration" screen, select t

f. Select Force to be a primary partition. g. Click OK. 6. Click New. a. Change the "File System Type" to swap. b. Make sure that only

7. Click Next 1.5 Network Configuration NOTE: The installer should have detected all of your NICs at this point. If it does not, then you may need

3. On the "Account Configuration" screen, type in the root password and confirmation. Click Next. It is also recommended that you create

Graphical Interface Configuration: In most cases, the installer will have automatically detected your video card configuration by this step. Simply c

Section 2. Special Cases 2.1 Booting from a Promise FastTrak TX2 2.1.1 Boot initialization string: NOTE: If installing to a Promise FastTrak TX2, y

Installing Red Hat Linux 7.3 Prepare the Installation Please refer to the Chapter 1 "Preparing the HP Server tc2120 for NOS Installation" f

Section 2. Updating the Server BIOS HP recommends that you update your server BIOS with the latest system BIOS version to enjoy the most recent compa

The installation program now displays a graphical interface. You can proceed through the customization of your installation. If you selected to insta

Choose Your Partitioning Strategy HP recommends using the default partitioning mode: Automatically partition and REMOVE DATA ("Disk Partitioning

Language Support Selection Review the Language Support setting and modify if necessary Time Zone Selection Review and modify as necessary Account Con

Boot Diskette Creation NOTE: HP recommends that you create a boot diskette that will allow you to boot and manage your server should you experience

Bios=0x80 Change: Boot=/dev/xxx To: Boot=/dev/sdX (Where /dev/sdX is the location of your Promise boot drive) 3. Change: Linear To: lba32 (Lo

• Kernel-2.4.18-17.7.x.i686.rpm may be found on the Web at ftp://ftp.redhat.com/pub/Red Hat/linux/updates/7.3/en/os/i686/kernel-2.4.18-18.7.x.i686.

• Modem 56k v92 • Promise IDE RAID PCI • HP Adaptec 29160 SCSI Controller Please refer to the product manual enclosed with your accessory for the

Section 1. Perform SuSE Linux 7.3 Installation Phase 1 – Launch the Installation Installing to Promise FastTrak100 TX2 1. Turn on the server and ins

Suggested Partitioning CAUTION: If you are installing to Promise FastTrak100 TX2, the boot partition and root partition must be formatted using th

b. Select Primary partition. c. Set the parameters for the boot partition as follows: Format (file system): ext2 Size: Start: Default End: Defa

Installing Microsoft Windows 2000 Server and Small Business Server 2000 Prepare the Installation Please refer to the Chapter 1 "Preparing the HP

Confirm Installation 1. The installation program will summarize the HDD partitioning information, boot manager installation location as well as the

4. Click Finish Installation to proceed to the initial login screen. Remove the CD from the drive. You are now ready to enter into your new SuSE 7.

92 HP CONFIDENTIAL Writer: Jimmy Chan File Name: 312977-006.doc Codename: Condor II Part Number: 312977-006 Last Saved On: 9/10/03 10:05 AM 8. Re