HP Integrity NonStop Release and Migration Uživatelský manuál Strana 180
- Strana / 320
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Running ZPHIRNM
G06.24 Software Installation and Upgrade Guide—528593-005
10-8
Verify That ZPHIRNM Ran Successfully
c. Repeat Steps a. and b. for the whatis_old file.
Verify That ZPHIRNM Ran Successfully
1. Review the log file.
2. If ZPHIRNM did not run successfully, correct whatever problems occurred and run
it again.
Two types of error and warning messages are issued during the renaming process:
•
If a fatal error occurs, ZPHIRNM immediately issues an error message and
stops.
•
A nonfatal error is one that affects processing only for a single subvolume. If a
nonfatal error occurs, ZPHIRNM issues an error message and attempts to
restore the subvolume it is currently processing to its original state.
°
If the subvolume is successfully restored, ZPHIRNM continues with the
next subvolume.
°
If the subvolume cannot be restored, ZPHIRNM issues an additional error
message and continues with the next subvolume.
°
If the subvolume was successfully processed, you can ignore warning
messages.
See the DSM/SCM User’s Guide for troubleshooting procedures and the
DSM/SCM Messages Manual for a complete list of ZPHIRNM messages.
- G06.24 Software 1
- Installation and 1
- Upgrade Guide 1
- Document History 2
- Part I. Upgrade Tasks 5
- 5. Installing the G06.24 RVU 6
- 9. Updating SCSI Boot Code 7
- 10. Running ZPHIRNM 7
- 11. Loading the G06.24 RVU 8
- Contents 10
- Versions (continued) 10
- Glossary 12
- What’s New in This Manual 15
- New and Changed Information 16
- About This Manual 17
- Notation Conventions 19
- General Syntax Notation 20
- Notation for Messages 21
- Overview of Installing G06.24 23
- TSM Client Applications 24
- OSM Client-Based Components 24
- DSM/SCM and the G06.24 RVU 27
- Updating Firmware 29
- ServerNet Adapter Firmware 29
- SPRs on page 3-8 30
- G06.24 31
- Concentrators 33
- Investigating a New RVU 35
- Installing a New RVU 35
- Components 38
- Notes on the FALLBACK Macro 40
- Notes on the CLEANOSS Macro 40
- Using ZPHIRNM 41
- NonStop TCP/IP FTP (G06.08) 42
- Products 43
- 4619 Disk Drives 44
- C++ (G06.20) 45
- DP2 (G06.16, G06.23, G06.24) 46
- OSS (G06.12 through G06.24) 48
- DSM/SCM (T6031D46) Fallback 49
- NonStop SQL/MP 50
- Installing SQL/MX Release 2.0 53
- (G06.08 through G06.24) 54
- Checking Current Version 55
- CSPOOL Set at HIGHPIN 56
- SWID (T9298D40^AAK) (G06.20) 57
- TMF (G06.23 and G06.24) 60
- TMF Fallback from G06.24 61
- Visual Inspect (G06.20) 62
- 2 G06.24 Upgrade Checklists 67
- G06.24 Upgrade Checklists 68
- G06.24 Upgrade Checklist 68
- D46 SPR of DSM/SCM 73
- Fallback SPRs 76
- Interoperability SPRs 77
- VST937.vsd 79
- Verify System Operations 83
- VST200.vsd 85
- Check Disk Subsystem Status 90
- Check the Tape Drive Status 93
- Record the Current SYSnn 94
- Back Up Important Files 94
- 5 Installing the G06.24 RVU 95
- Installing the G06.24 RVU 100
- Interface (ZPHITI) 113
- (ZPHITI) 114
- Microcode (Pre-G06.06) 119
- Replacing the Disk Bootstrap 119
- Firmware 121
- Before You Begin 123
- SP Firmware (Using TSM) 125
- Application 128
- VST647.vsd 131
- VST680.vsd 134
- (Using TSM) 135
- (SPs) list 139
- 9. Click Close 139
- Connection 140
- VST939.vsd 141
- VST949.vsd 142
- VST966.vsd 143
- Connection) 148
- System Console (Optional) 148
- (Optional) 150
- Updating Processor Boot Code 151
- Check Processor Status 153
- CPUCODE9 156
- VST955vsd 159
- Reset or Equivalent 160
- Code (Both for OSM and TSM) 166
- Updating SCSI Boot Code 169
- (Pre-G06.08 RVU) 169
- Necessary) 170
- 10 Running ZPHIRNM 173
- Subvolume 174
- Stop All Applications 175
- Drain the Spooler 175
- Using ZPHIRNM PREVIEW Mode 176
- Steps for Running ZPHIRNM 177
- Running ZPHIRNM 179
- 11 Loading the G06.24 RVU 181
- Halt the Processors 182
- Loading the G06.24 RVU 183
- Low-Level Link 184
- The Reset Operation 188
- 12 Resuming Normal Operations 189
- Resuming Normal Operations 190
- Complete 191
- (Overview) 194
- Configure the Spooler 197
- Before Starting DSM/SCM 198
- Initialize SQL 198
- Configure OSS 201
- Configure SMF (Optional) 202
- Part II. Fallback Tasks 205
- 13 Preparing to Fall Back 207
- Summary of Fallback Tasks 208
- DLL (Dynamic-Link Libraries) 209
- Open System Services (OSS) 210
- OSM and TSM 210
- SQL/MX 2.0 211
- WAN Manager (T8365) 211
- Preparing to Fall Back 212
- 4> TMFCOM START TMF 213
- 6> RUN STARTSCM 213
- Submit a Backout Request 215
- Monitor the Backout Process 219
- Versions 221
- Version (Using TSM) 222
- Version (Using OSM) 225
- Previous Software Revision 229
- Run ZPHIRNM 230
- Software Revision 231
- Loading the Previous RVU and 233
- Prepare to Stop the System 234
- SYSnn and CONFxxyy 235
- Resume Normal Operations 236
- Configure Spooler 237
- Operations 238
- Using DSM/SCM to Install SPRs 239
- Install SPRs With DSM/SCM 240
- Determine the Current SYSnn 241
- Build the New Revision 243
- If a System Load Is Required 247
- Perform a System Load 248
- Client SPRs 251
- Software 252
- Identification (SWID) SPR 253
- 8. Click OK 258
- D46 SPR and SWID 260
- Revision 261
- Restart Applications 265
- Verify That SWID Is Installed 267
- D46 Version of DSM/SCM 268
- 4. Click Start 279
- Update Fails on page C-7 282
- Update SWAN Firmware 284
- Or (using SCF) enter: 285
- VST400.vsd 286
- Or (using SCF), enter: 289
- Verify That CLIPs Are Stopped 290
- Code File 291
- T7954Vnn^ddmmmyyyy^AAN) 292
- VST440.vsd 293
- VST960.vsd 295
- VST951.vsd 296
- VST961.vsd 297
- Glossary-2 302
- Glossary-3 303
- Glossary-4 304
- Glossary-5 305
- Glossary-6 306
- Glossary-7 307
- Glossary-8 308
- Glossary-9 309
- Glossary-10 310
- Glossary-11 311
- Glossary-12 312
- Glossary-13 313
- Glossary-14 314
- Special Characters 320
Související produkty a manuály pro Software HP Integrity NonStop Release and Migration
Software HP 2600-PWR Uživatelský manuál
(418 stránky)
(418 stránky)
Software HP 5992-3193 Uživatelský manuál
(66 stránky)
(66 stránky)
Software HP Laptop 7.2 Uživatelský manuál
(53 stránky)
(53 stránky)
Software HP 1.5TB Uživatelský manuál
(216 stránky)
(216 stránky)
Software HP Integrity NonStop H-Series Rychlý návod
(35 stránky)
(35 stránky)
Software HP 2/8q Uživatelský manuál
(188 stránky)
(188 stránky)
Software HP T5700 Uživatelský manuál
(76 stránky)
(76 stránky)
Software HP XP512 Uživatelský manuál
(99 stránky)
(99 stránky)
Software HP XP10000 Uživatelská příručka
(109 stránky)
(109 stránky)
Software HP NetMail/3000 Uživatelský manuál
(102 stránky)
(102 stránky)
Software HP Moonshot-45G Uživatelský manuál
(76 stránky)
(76 stránky)
Software HP T5300 Uživatelský manuál
(338 stránky)
(338 stránky)
Software HP X9320 Uživatelská příručka
(150 stránky)
(150 stránky)
Software HP 48gII Uživatelský manuál
(175 stránky)
(175 stránky)
Software HP B6191-90029 Uživatelský manuál
(140 stránky)
(140 stránky)
Software HP 250m Čistý list
(95 stránky)
(95 stránky)
Software HP 5992-3838 Uživatelský manuál
(78 stránky)
(78 stránky)
Software HP XP20000 Uživatelský manuál
(170 stránky)
(170 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce