Hp StorageWorks 3000 RAID Array Uživatelský manuál Strana 124
- Strana / 126
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
5-4 Command Console V2.2 for the RAID Array 3000 (Pedestal and Rack Mount Models)
Troubleshooting Client and Agent
Connections
■ Make sure the system names used for the client and agent match each
other consistently. As a general rule, always use lowercase letters when
entering names.
■ If you have entered the host name in the HOST file, verify that it is
spelled correctly and that it is in lowercase letters. The host name is not
required in this file, but TCP/IP will look here first when resolving host
names. The HOST file is on the client system in the following directory:
■ On Windows NT, \WINNT\SYSTEM32\DRIVERS\ETC
■ Make sure you have the correct port numbers in the client’s SERVICES
file as follows:
■ On Windows NT, look in the
\WINNT\SYSTEM32\DRIVERS\ETC\SERVICES file.
Be sure the port entries are followed by a carriage return if they are the last
entries in the file as shown below:
spgui 4998/tcp
spagent3 4994/tcp
■ Make sure the command console agent on the host system is using a
correct host name to recognize the client. If the host system is Windows
NT, run the Agent Configuration Utility (H22AgntCfgWiz.exe) or
examine the client.ini file on the host system. On other host systems,
look at the client.ini file.
■ If you are using a Windows NT Client, run NETSTAT at the MS-DOS
prompt to check the TCP/IP active connections.
■ Check the client name that the agent’s host system sees is the same as
the name specified in the agent's client.ini file. Run NETSTAT at the
MS-DOS prompt on the agent, if you are using a Windows NT host
system, and check the TCP/IP active connections.
■ Make sure the Agent’s host system has been configured to recognize the
client by its assigned name rather than by an alias name. If the host
system has been configured to recognize the client by an alias name,
remove the alias name from the system’s hosts file.
NOTE: Always reboot the client system after making changes to the hosts or services file.
■ Command Console does not support DHCP (Dynamic Host Configuration Protocol)
connections, where Clients are configured for TCP/IP at system startup time.
- Compaq StorageWorks 1
- Contents 3
- Chapter 2 4
- Chapter 3 4
- Chapter 4 5
- List of Figures 6
- List of Tables 8
- About This Guide 9
- Related Documents 11
- Text Conventions 12
- Symbols in Text 12
- Symbols on Equipment 13
- Compaq Website 15
- Compaq Authorized Reseller 15
- Introduction 17
- About the Client 18
- About the Agent 18
- Local Serial Port Connection 21
- Windows 2000 22
- Introduction 1-7 23
- Available Connections 24
- Command Console’s Features 25
- Table 1-6 26
- Console Client 27
- 4. Double-click Setup 28
- a. Command Console Client 30
- b. HSZ22 Client 30
- Connection 36
- Installing the Agent Software 44
- Network Connections) 46
- Using Command Console 47
- About the AES 48
- Choosing a Connection Method 51
- Storage window 52
- Reboot your system 55
- Connecting Over a Network 58
- Using the Navigation Window 61
- Deleting a System 63
- Renaming a Folder 64
- Properties 65
- Opening a Storage Window 66
- Using Command Console 3-21 67
- Environment, and Cache 67
- Using Command Console 3-23 69
- User’s Guide 71
- Adding Devices 73
- Creating a Virtual Disk 73
- Deleting Virtual Disks 81
- Modifying Virtual Disks 82
- (Network Only) 84
- Password Security 85
- Clearing Failed Devices 86
- Using Configuration Files 86
- Printing a Configuration File 87
- Figure 3-39. Environment tab 89
- Setting Up Pager Notification 90
- Setting Pager Preferences 91
- Defining a User Profile 92
- Table 3-1 95
- Pager Critical Event Codes 95
- Setting Up Notification Lists 96
- Creating a Notification List 97
- Menus, and Tools 99
- Menus and Commands 100
- Navigation Window 101
- System Folders 102
- General Folders 103
- Controller Folders 103
- Navigation Window Menu Bar 104
- Navigation Window Toolbar 105
- Navigation Window Status Bar 106
- Storage Window 107
- Storage Window Menu Bar 108
- Storage Window Toolbar 109
- Virtual Disk Window 110
- Details View 112
- Device Window 113
- Device Properties 114
- View Options 117
- Grid View 117
- Cabinet View 118
- Change View 119
- EMU Icon 120
- Chapter 5 121
- Backing up Files 121
- Updating Controller Firmware 122
- Initializing Virtual Disks 123
- Connections 124
- Windows NT Event Logging 125
Související produkty a manuály pro Úložný prostor Hp StorageWorks 3000 RAID Array
(37 stránky)
(78 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce