HP Value 2D Wireless Scanner Uživatelský manuál

HP Value Wireless Barcode ScannerUser Guide

TabScan the following bar code to set the scanner back to the factory defaults.Figure 1-14 Set Base DefaultsNOTE: Scanning the “Set Base Defaults” ba

Figure 1-19 9Figure 1-20 Exit Global Suffix ModeFigure 1-21 Exit Programming ModeVolumeScan the following bar code to set the scanner back to the f

Figure 1-24 Set HP DefaultsFigure 1-25 OffFigure 1-26 LowFigure 1-27 MediumFigure 1-28 High6 Chapter 1 Quick setup

2 Product featuresHP Value Wireless Barcode ScannerWith rich feature sets and extensive options, the HP Value Wireless Barcode Scanner represents the

3 Safety and maintenanceErgonomic recommendationsWARNING! In order to avoid or minimize the potential risk of ergonomic injury follow the recommendati

CleaningExterior surfaces and scan windows exposed to spills, smudges or debris require periodic cleaning to ensurebest performance during scanning op

4 Setting up and using the scannerFollow the steps below to connect and get the scanner up and communicating with its host.1. Configure the Base Stati

Figure 4-2 Lock Lever Disengaged2. Engage the locking mechanism by pushing up the lever as far as it will go.Figure 4-3 Lever in Locked PositionNOTE

Connecting the base stationYou can connect the base station to a terminal, PC, or other host device. Turn off the host before connectionand consult th

4. Connect to an AC adapter, and plug the AC power cord into the (wall) outlet.Figure 4-6 Connecting the Base Station1 Interface cable 4 AC/DC adapte

© 2014 Hewlett-Packard DevelopmentCompany, L.P.Bluetooth is a trademark owned by itsproprietor and used by Hewlett-PackardCompany under license. Micro

2USB 5Keyboard wedge3Wand Power Connection — Plug the AC adapter into an approved AC wall socket with the cable facing downwardsto prevent undue str

No. Icon LED STATUS2Charging Red On = the Battery is charging.2Charge completed Green On = the Battery is completely charged.2Charging + Chargecomplet

WARNING! Do not place the battery pack in fire or heat.Do not connect the positive terminal and negative terminal of the battery pack to each other wi

The useful life of LI batteries depends on usage and number of charges, etc., after which they should beremoved from service, especially in mission cr

Using the scannerThe scanner normally functions by capturing and decoding codes. The aiming system is activated on triggerpull and indicates the cente

Linking the scannerLink RF devices to baseFor RF devices, before configuring the interface it is necessary to link the handheld with the base.To link

NOTE: The scanner can be set up to require a PIN code when connecting. If you want to set up a PIN, orwhen adding new equipment to a system that uses

Figure 4-23 HID Alt Mode = ONPower offScan the bar code below to shut off power to the handheld until the next trigger pull.Figure 4-24 Power OffCou

Figure 4-27 Country Mode = BelgiumFigure 4-28 Country Mode = BritainFigure 4-29 Country Mode = Croatia*Figure 4-30 Country Mode = Czech Republic*F

Figure 4-35 Country Mode = Hungary*Figure 4-36 Country Mode = ItalyFigure 4-37 Country Mode = Japanese 106-key*Figure 4-38 Country Mode = Lithuani

About This GuideThis guide provides information on setting up and using the HP Value Wireless Barcode Scanner.WARNING! Text set off in this manner ind

Figure 4-43 Country Mode = SpainFigure 4-44 Country Mode = SwedenFigure 4-45 Country Mode = Slovakia*Figure 4-46 Country Mode = Switzerland**Suppo

Figure 4-49 Caps Lock State = Caps Lock ONFigure 4-50 Caps Lock State = AUTO Caps Lock EnableSelecting the base interface typeUpon completing the ph

Figure 4-52 Select RS-232 Wincor-NixdorfFigure 4-53 Select RS-232 OPOS/UPOS/JavaPOSFigure 4-54 Select USB-COM-(to simulate RS-232 standard interfac

Figure 4-59 Select KBD-AT-ALT-NK (Keyboard Wedge for IBM AT PS2 with alternate key encoding butwithout external keyboard)Figure 4-60 Select KBD-XT (

Figure 4-67 Select USB Keyboard (USB Keyboard with standard key encoding)Scancode tablesReference to the PRG for information about control character

5 Programming the scannerThe scanner is factory-configured with a set of standard default features. After scanning the interface barcode from the Inte

Reading parametersPoint the scanner at the target and pull the trigger to enable the aiming system and the illuminator (redbeam) to decode the barcode

6 Operating modesScan modesThe imager can be set to operate in one of several scanning modes.Trigger Single: When the trigger is pulled, scanning is a

Figure 6-4 Scan Mode = Trigger Pulse MultipleFigure 6-5 Scan Mode = FlashingFigure 6-6 Scan Mode = Always OnFigure 6-7 Scan Mode = Stand ModePick

Figure 6-10 Pick Mode = EnableMultiple labels in a volumeEnables/disables the ability of scanner to decode multiple labels in the same image. Several

iv About This Guide

A Technical supportOnline technical supportFor the online access to technical support information, self-solve tools, online assistance, community foru

B Technical specificationsThe following table contains physical and performance characteristics, user environment and regulatoryinformation.Item Descr

Depth of Field (Typical) 1 Symbology SR:10mil: 0" - 8.7" (0 - 22cm)20mil: up to 17.7” (up to 45cm)EAN 7.5mil: 0" - 5.9" (0 - 15cm)

Decode Capability 1D Bar Codes RS-232 Std, RS-232 Wincor-Nixdorf, RS-232 OPOS, USB Com Std., USB Keyboard, USB Alternate Keyboard, USB OEM, Keyb

LED and beeper indicationsThe scanner’s beeper sounds and its LED illuminates to indicate various functions or errors on the scanner.An optional “Gree

INDICATION DESCRIPTION LED BEEPERLabel Programming ModeAcceptance of ProgrammingConfiguration option(s) havebeen successfully programmedvia labels and

C Hex-numeric keypadUse the bar codes that follow to enter numbers as you would select digits/characters from a keypad.Figure C-1 0Figure C-2 1Figur

Figure C-8 7Figure C-9 8Figure C-10 9Figure C-11 AFigure C-12 BFigure C-13 CFigure C-14 DFigure C-15 E41

Figure C-16 FFor HID Variable Pin Code only:If you make a mistake, scan the CANCEL barcode below to abort and not save the entry string. You can then

Table of contents1 Quick setup ...

Interface selection ... 25Co

1 Quick setupUse the bar codes in this chapter to perform quick setup procedures for common tasks.Scan the following bar codes in the order listed bel

OPOS driverThe scanner by default is shipped in the human interface device (HID) keyboard emulation mode. In order touse the barcode scanner with OLE

Figure 1-8 Set HP DefaultsFigure 1-9 Set Global SuffixFigure 1-10 0Figure 1-11 DFigure 1-12 Exit Global Suffix ModeFigure 1-13 Exit Programming