Hp ProLiant DL388e Gen8 Server Uživatelský manuál Strana 20
- Strana / 136
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Operations 20
IMPORTANT: The requirement of extending or removing the server from the rack when
performing installation and maintenance procedures depends on the rail system used:
• If using a ball-bearing rail system, you can perform most installations and maintenance by
simply extending the server from the rack.
• If using a friction rail system, to perform installations or maintenance that requires access panel
removal, remove the server from the rack.
To extend the server from an HP, Compaq-branded, Telco, or third-party rack:
1. Power down the server (on page 19).
2. Remove all power:
a. Disconnect each power cord from the power source.
b. Disconnect each power cord from the server.
3. Disconnect all peripheral cables.
WARNING: To reduce the risk of personal injury or equipment damage, be sure that the rack is
adequately stabilized before extending a component from the rack.
WARNING: To reduce the risk of personal injury, be careful when pressing the server rail-release
latches and sliding the server into the rack. The sliding rails could pinch your fingers.
4. Pull down the quick release levers on each side of the server.
5. Extend the server on the rack rails until the server rail-release latches engage.
If the server does not extend from the rack, use a T-25 Torx screwdriver to loosen the screws located
within the lever housing.
6. After performing the installation or maintenance procedure, slide the server into the rack.
- User Guide 1
- Contents 3
- Contents 4 4
- Contents 5 5
- Contents 6 6
- Component identification 7
- Front panel LEDs and buttons 8
- Rear panel components 9
- Rear panel LEDs and buttons 11
- System board components 12
- Item Description 13
- DIMM slot locations 14
- System maintenance switch 14
- NMI functionality 14
- Drive numbering 15
- Drive LED definitions 16
- FBWC module LED definitions 16
- Fan locations 18
- Operations 19
- Remove the access panel 22
- Install the access panel 23
- Remove the air baffle 23
- Install the air baffle 23
- Remove the PCI riser cages 24
- Install the PCI riser cages 25
- Optimum environment 27
- Temperature requirements 28
- Power requirements 29
- Server warnings and cautions 30
- Rack warnings 31
- Installing hardware options 32
- Registering the server 34
- Introduction 35
- Security bezel option 35
- Drive options 35
- Installing a hot-plug drive 36
- Rear drive cage options 37
- Drive cable options 44
- Mini-SAS cable option 45
- Mini-SAS Y-cable options 46
- Controller options 47
- Optical drive option 52
- Hot-plug fan module option 53
- • In a redundant fan mode: 54
- Memory options 58
- HP SmartMemory 59
- DIMM identification 60
- Memory protection modes 61
- Memory population guidelines 62
- Installing a DIMM 64
- Processor option 65
- Expansion board options 70
- GPU power cable option 72
- Cabling 81
- 4 SFF SATA cabling 82
- 6 LFF SATA cabling 82
- 6 SFF SATA cabling 83
- 8 LFF cabling 83
- 8 SFF cabling 85
- 8+8 SFF cabling 87
- 2 LFF rear drive cabling 90
- 2 SFF rear drive cabling 91
- Capacitor pack cabling 92
- Cabling 93 93
- Optical drive cabling 94
- GPU power cabling 94
- Dual-rank GPU 95
- Primary GPU power cabling 95
- Secondary GPU power cabling 96
- Server mode 97
- HP product QuickSpecs 97
- HP iLO Management 97
- Active Health System 98
- Intelligent Provisioning 99
- HP Insight Diagnostics 100
- Erase Utility 100
- HP Insight Online 101
- HP Service Pack for ProLiant 102
- HP ROM-Based Setup Utility 102
- Using RBSU 103
- Auto-configuration process 103
- Configuring AMP modes 104
- Boot options 104
- Utilities and features 105
- ROMPaq utility 106
- Automatic Server Recovery 106
- USB support 106
- Redundant ROM support 106
- Keeping the system current 107
- ProLiant servers 108
- Troubleshooting 109
- System battery replacement 110
- Regulatory information 112
- Electrostatic discharge 113
- Specifications 114
- Specification Value 116
- Support and other resources 120
- Customer Self Repair 122
- Reparo feito pelo cliente 124
- Acronyms and abbreviations 128
- Documentation feedback 132
- Index 133 133
- Index 134 134
- Index 135 135
- Index 136 136
Související produkty a manuály pro Počítačový hardware Hp ProLiant DL388e Gen8 Server
(86 stránky)
(93 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.087 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce