Hp Integrity rx4610 Server Uživatelský manuál Strana 96
- Strana / 249
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Chapter 8 Server Management Boards
88
7. Rotate the levers downward to press the I/O Baseboard securely into the
Sideplane.
8. Connect the Internal SCSI cable to the front of the I/O Baseboard.
9 Install the plastic shield over the I/O Baseboard and tighten the two
thumbscrews that secure the shield and the I/O Baseboard in the chassis.
10. Connect the PCI LED cable.
11. Install the DC-DC converters on the Sideplane. The voltages are marked
on the power supplies and near the sockets on the baseboard.
12. Install the protective cover over the DC-to-DC converters on the
Sideplane, and secure the cover with the thumbscrew.
13. Connect the cable to the external SCSI port at both ends: one to the I/O
Baseboard and the other secured to the rear of the chassis with the captive
thumbscrew.
14. Install the Legacy I/O board and cables as described in “Installing the
Legacy I/O Board”.
15. Install the non-hot plug PCI and hot plug PCI adapter boards as described
in “Installing Accessory Boards” in Chapter 7.
16. Install all PCI slot plastic dividers (I/O Card Dividers) as required.
17. Install the top cover as described in “Replacing the Top Cover” in
Chapter 2.
18. Attach the non-hot plug PCI adapter board cover and secure it with its
screw.
19. Close the PCI I/O access door, and secure it with the two captive
thumbscrews.
20. Reconnect the power cables.
- User Guide 1
- Audience Assumptions 2
- Contents 3
- Activity LED 11
- Open/Close Button 11
- Activity 12
- LCD DISPLAY 13
- • +48 V 14
- • +12 V standby 14
- Power Supply Indicators 15
- Rear View 16
- Legacy I/O Panel 17
- Powering-Up the HP Server 19
- Powering-Down the HP Server 20
- Server 21
- Main Cover 22
- Tools Required 23
- Removing the Top Cover 23
- Replacing the Top Cover 24
- 3 Installing Fans and Power 27
- Supplies 27
- Removing the 172 mm Fans 28
- Installing the 172 mm Fans 29
- Hot Swapping the 120 mm Fans 30
- Installing the 120 mm Fans 31
- Hot Swapping Power Supplies 32
- Removing a Power Supply 33
- Installing a Power Supply 34
- Mass Storage Guidelines 35
- Boot Priority 36
- Removing a Hard Disk Drive 38
- Installing the DVD Drive 42
- Removing the Hard Disk Bay 44
- Installing the Hard Disk Bay 45
- Removing the SCSI Backplane 46
- 1. Disconnect the cable 48
- 2. Remove the two screws 48
- Converters 52
- Removing Memory Boards 53
- Installing Memory Boards 55
- Installing DIMMs 57
- Removing a Processor 68
- Figure 6-7. The Triple Beam 74
- IRQ Settings 78
- Installing Accessory Boards 79
- PCI Hot Plug Slots 83
- Non PCI Hot Plug Slots 83
- Removing Accessory Boards 85
- 8 Server Management Boards 89
- Hot Swap Controller (HSC) 91
- I/O Baseboard 92
- Remove protective 93
- Sideplane cover 93
- Installing the I/O Baseboard 95
- Sideplane Board 97
- PCI Hot Plug LED Board 100
- Legacy I/O Board 102
- Server Management 103
- DVD Cable 103
- Floppy Disk 103
- Drive Cable 103
- Bracket 107
- 9 Connecting the Monitor 113
- Keyboard, and Mouse 113
- Introduction 115
- Configuring the HP Server 115
- Accelerated Cool Down 123
- FRB3 Timeout 124
- Using BIOS Setup 131
- Using the SELViewer Utility 141
- Using the SDR Viewer Utility 145
- Upgrading the Server 150
- Clearing CMOS by Jumper: 152
- Upgrading the Firmware 155
- Parameters 160
- Comparing the FRU File 166
- Loads Specified SDR File 166
- Comparing the SDR File 166
- Configuration File 167
- Cleaning Up and Exiting 168
- 11 Troubleshooting 169
- Troubleshooting Sequence 170
- Chapter 11 Troubleshooting 171
- BIOS Error Codes\Messages 181
- Beep Codes 186
- Table 11-1. BMC Beep Codes 187
- Types of Memory Tests 188
- User Notification 189
- Base Memory Test 191
- User Action 192
- Error Logging 193
- Extended Memory Test 197
- Examples 199
- Memory Test Duration 201
- Aborting the Memory Test 201
- Setup Dialog 202
- A Specifications 207
- Requirements 208
- Appendix A Specifications 209
- VGA Video Port 211
- Keyboard and Mouse 212
- Parallel Port 213
- Serial Ports A and B 214
- Universal Serial Bus (USB) 215
- Figure A-7. SCSI Connector 216
- Figure A-8. IDE Connector 217
- Information on Jumpers 222
- J4A1 J7A1 229
- J7A1 J7A1 231
- I/O Baseboard Jumpers 233
- Determining DC-to-DC Status 236
- Worksheet 239
- C INI File Format 241
- Appendix C INI File Format 242
- Data Markers 243
- BMC, 178, 179 245
- Fan Fail LED, 2 246
- Front Panel LCD, 2 246
- General Fault LED, 2 246
- INIT, 2 247
- System Power LED, 2 249
Související produkty a manuály pro Počítačový hardware Hp Integrity rx4610 Server
(114 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce