Hp StorageWorks Scalable File Share Uživatelský manuál Strana 227
- Strana / 362
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Server fails to boot during installation 9–3
9.1 Server fails to boot during installation
If a server fails to boot during the installation process, it may be as a result of incorrect firmware versions
on the server. Make sure that the firmware versions on the HP Integrated Lights-Out Management Controller
and the BIOS - System ROM on the server meet the specifications listed in the HP StorageWorks Scalable
File Share Release Notes.
In addition, check that the MAC address of each server is correct. The MAC address is displayed by the
show server command. If the MAC address is wrong (or not set), run the scan mac command on the
administration server.
9.2 Server fails to boot
If a server fails to boot, review the progress of the boot process by connecting to the server console as shown
in the following example, where the server is south3:
# hpls_console --server south3 --remote
If you see messages similar to the following:
Attempting Boot From CD-ROM
Attempting Boot From Floppy Drive (A:)
Attempting Boot From NIC
Attempting Boot From Hard Drive (C:)
LI
this is an indication that the PXE DHCP request timed out, and the local disk on the Object Storage Server
contains an incomplete bootsector.
To recover from this situation, shut down the server and then boot it again, as shown in the following
example:
sfs> shutdown server south3 wait=0
sfs> boot server south3
9.3 Server stops responding
If it appears that a server has stopped responding, report the problem to your HP Customer Support
representative. Your representative may ask you to force the server to crash, and to provide a number of files
to assist in diagnosing the problem, as follows:
• A crash dump file.
If your HP Customer Support representative asks you to provide a crash dump file, perform the
following steps:
1. From the administration server, connect to the serial console of the server that has stopped
responding, as shown in the following example:
# hpls_console --server south4
2. Press the Esc key (twice, if the iLO firmware on the server that has stopped responding is at
Version 1.70 or Version 1.75; once, if the firmware is at any other version) then immediately
enter the following characters. Do not include any spaces:
]]8
3. Again, press the Esc key (twice, if the iLO firmware is at Version 1.70 or Version 1.75; once, if
the firmware is at any other version) then immediately enter the following characters. Do not
include any spaces:
]]c
4. Exit the serial console immediately.
- System User Guide 1
- Version 2.2 1
- Contents 3
- 4 Viewing system information 4
- A CLI commands 9
- About this guide 11
- HP SFS documentation 12
- Documentation conventions 12
- Naming conventions 13
- For more information 13
- Providing feedback 13
- Safety considerations 15
- 1Overview 17
- 1.1 Product overview 18
- 1.1.2 Overview of HP SFS 19
- 1.1.3 HP SFS configurations 20
- 1.1.3.2 Storage 21
- 1.1.3.3 Network connections 23
- 1.1.3.3.2 Management network 24
- 1.3 Supported hardware 25
- Overview1–10 26
- 2 The sfsmgr utility 27
- 2.1 Overview 28
- 2.2 Starting the SFS CLI 28
- 2.3 Running sfsmgr commands 29
- The sfsmgr utility2–6 32
- 3 Operating the system 33
- 3.1 Booting the system 34
- 3.2 Shutting down the system 36
- 3.3 Booting a server 36
- 3.4 Booting multiple servers 37
- 3.7 Stopping a file system 39
- 3.8 Starting a file system 40
- 3.11 Managing licenses 47
- 3.12 Managing remote access 53
- 3.12.3 Viewing authorizations 55
- 4Viewing system information 57
- 4.4 Viewing LUN information 67
- 4.5 Viewing array information 69
- 4.6 Viewing event logs 72
- 4.6.1.1 Event filters 73
- 4.6.1.2 Event severity 73
- 4.6.1.3 Event facility 73
- LUNs — EVA4000 storage 88
- File system name 100
- Mount point 100
- Stripe size 100
- MDS LUNs 100
- Number of OST services 101
- Interconnects 102
- Quota options 102
- Mount options 102
- Stripe count 102
- 5.4 Operating a file system 111
- 5.7 Managing quotas 121
- command on 123
- # lfs quotacheck -ug /data 124
- 5.7.3 Checking quota limits 125
- 5.10 Deleting file systems 127
- 6.1 Verifying the system 132
- Verifying the system 6–5 135
- # ssh south3-adm hostname 150
- Sequential test 151
- Parallel test 152
- Incremental test 152
- Latency test 157
- Unidirectional bandwidth test 158
- Verifying the system 6–33 163
- 6.2 Managing email alerts 169
- 6.2.4 Default email alerts 171
- Managing email alerts 6–43 173
- 6.2.5 Modifying email alerts 174
- 6.2.6 Creating email alerts 174
- 6.2.7 Viewing email alerts 175
- 6.2.9 Deleting email alerts 176
- 6.5 Removing log files 180
- 6.6.1 Overview 181
- 6.6.2 Viewing the IML 181
- 6.6.3 Clearing the IML 181
- Configuration impact 201
- Object Storage Server 202
- Number FCA2214 DC) 204
- [root@south4 var]# raw -qa 206
- 8.2 Upgrading firmware 214
- # service cluster stop 216
- 8.3.3 Adding SFS20 arrays 222
- 8.3.4 Removing SFS20 arrays 222
- 9Troubleshooting 225
- 9.2 Server fails to boot 227
- 9.3 Server stops responding 227
- /proc/fs/lustre/mds/mds2 247
- # repair-lfsck -f scratch 250
- Troubleshooting9–34 258
- Remedial action 261
- 9.27.2.1 Recreating files 262
- 9.30 Accessing consoles 275
- 9.31.1.2 Using a Web browser 276
- 9.32 Troubleshooting licenses 277
- 9.36 System log files 288
- ACLI commands 295
- A.1 General information 296
- A.2 accept license command 297
- A.3 activate ost command 297
- A.4 boot server command 297
- A.5 configure commands 298
- A.5.2 configure server 300
- A.6 create commands 301
- A.6.3 create authorization 302
- A.6.4 create database_backup 302
- A.6.5 create filesystem 303
- A.7 deactivate ost command 304
- A.8 delete commands 304
- A.8.2 delete array 305
- A.8.3 delete attribute 305
- A.8.4 delete authorization 305
- A.9 disable commands 306
- A.9.2 disable server 307
- A.10 enable commands 308
- A.11 help command 309
- A.12 kill command command 309
- A.13 modify commands 310
- Interactive mode 311
- Scripted mode 311
- A.14 monitor command command 312
- A.15 pause filesystem command 312
- A.16 quit command 313
- A.18 scan mac command 313
- A.19 set commands 314
- A.19.2 set attribute 315
- A.19.3 set lun 316
- A.19.4 set nics 317
- A.19.5 set password 318
- A.19.6 set server 318
- A.20 show commands 319
- A.20.4 show authorization 320
- A.20.5 show commands 320
- A.20.6 show database_backups 321
- A.20.7 show filesystem 321
- A.20.8 show license 321
- A.20.9 show log 321
- Examples 322
- A.20.10 show lun 323
- A.20.11 show network 323
- A.20.12 show ost 323
- A.20.13 show server 324
- A.20.14 show support 324
- A.20.15 show system 324
- A.20.16 show version 324
- A.21 shutdown server command 325
- A.22 start filesystem command 325
- A.23 stop filesystem command 326
- A.24 syscheck command 326
- A.26 ! command 328
- B Performance figures 329
- B.1 I/O performance 330
- SFS20 storage — 250GB disks 331
- SFS20 storage — 5000GB disks 331
- B.2 Network performance 332
- B.3 SFS20 array configuration 333
- RAID5 and ADG Read Bandwidth 334
- 64 clients 336
- 128 Clients 336
- 192 clients 336
- Bandwidth vs Clients 337
- Single Client Varying OSTs 338
- 1500 MTU Average Write MB/sec 339
- 9000 MTU Average Read MB/sec 340
- C.1 EVA4000 storage examples 344
- EVA4000 storage examples C–3 345
- C.2 SFS20 storage examples 346
- SFS20 storage examples C–5 347
- D.1 RAID rebuild information 350
- E HP SFS specifications 351
- HP SFS specificationsE–4 354
- Glossary 355
- Glossary–2 356
- Glossary–3 357
- Glossary–4 358
- 9-24, 9-25 361
Související produkty a manuály pro Úložný prostor Hp StorageWorks Scalable File Share
(107 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce